answersLogoWhite
Chevy Impala
Chevy Silverado
Lincoln Town Car
Door Panels and Handles

How do you remove the door panel of a 97 town car sig series?

535455

Top Answer
User Avatar
Wiki User
2011-09-13 06:21:09
2011-09-13 06:21:09

Its been a while since I sold my 95 town car but if i can remember correctly there are plastic covers on the pull handle that need to be removed, behind those there are 2 screws. After that depending on the front or back panel there are a couple other screws. On the front there is one inside the armrest pocket and another on the edge of the panel. The rear has one on the edge. After that it is just a matter of gently pulling the panel off, there are a dozen or so pop clips holding it in place. Its usually a good idea to replace them when you reinstall the panel so its not loose or rattely. Remember its been a while since I had mine so check around good to be sure you get all the screws out before popping the panel off.

1

Related Questions

User Avatar

Unscrew the door lock.Remove the door pull.Take out any remaining screws on the door panel.Remove the master power switch.Pull the panel from the door.

User Avatar

On a rear door you have to:Remove the door switches.Remove the door pull.Next unscrew any remaining screws in the door panel.Unscrew the door lock.Use a putty knife and pry the door panel away from the door.

User Avatar

I have included a link below in the related link section that will show you how to remove the door panel on a 2004-2007 Chrysler Town & Country. Hope this helps you out.

User Avatar

You have to:Remove the door panel.Undo the rods off of the handle.unbolt the door handle from the inside of the door.

User Avatar

The rear door panel is held in place by eight retaining clips into screws. Remove the screws near the door handle. Pry outward on each retaining clip. The rear door panel will come off.

User Avatar

Remove the door panel and you can see two nuts holding the door handle. Just tighten them.

User Avatar

First remove the door panel.Then remove the moisture barrier.Next remove the window motor from the window regulator.

User Avatar

You would need to take the door panel off and then remove the three bolts that hold the mirror onto the door.

User Avatar

take out the screws on the door and pull out the panel starting from the bottom and at the top has to lefted up since it slides next to the window. Becareful with the wires for the controls.

User Avatar

It is located on the computer inside the drivers door. Just remove the door panel and it will be on the computer.

User Avatar

Yes, remove the door panel, remove the window motor. You should be able to lift the window up.

User Avatar

it's 2 screws located where the leather pull handle meet the door panel. remove those and the rest is just pull clips located behind the door panel.once you done that you got access to 1 bolt that holds that side mirrow.

User Avatar

there are screws in the door, and holding the handle on. You can get to the ones holding on the handle by pulling off the covers on each side of the door handle inside.

User Avatar

You must remove door panel to acess bolts that secure mirror to door. Remove all parts securing mirror and install in reverse order with new mirror.

User Avatar

remove retaining screw,and power window bezel. Raise plate disconnect wires.remove all retaining screws from door. window should be in closed position. pull panel away slightly and check for any other wires that need disconnecting

User Avatar

Remove drivers door panel and disconnect the wires from the button and cross them, make sure you have battery power. Should open. Replace door panel.

User Avatar

its in the driver side door in the actual power door panel

User Avatar

need torx bit (t 20 or 25 I think). torx screw in UNDERSIDE of leather door handle pull, holes in underside of plastic woodgrain at edges of leather door pull. 2-3 Phillips screws in bottom of door panel (in carpet). unscrew door lock knob. pry door panel away...

User Avatar

You need to remove the screws and then take a pry bar and stick it under the panel. Lift the bar until you hear some pops and continue all the way around the door panel. You might brake some pins off, that's what I'm trying to find now. Hope you can get it.

User Avatar

Remove the inside door panel of your 1988 Lincoln Town Car. Remove the wiring harness from your window motor. Remove the window motor retaining screws. Reverse the process to install a new window motor.

User Avatar

Remove the speaker grill. There is a single screw. Take that off and the panel can be removed. remove the handle screws cover and remove the screws. Remove the opening door handle screws. there are two of those. You will be able to see then if you look behind the handle on the black cover.

User Avatar

THESE RELAYS ARE UNDER THE GLOVE BOX. REMOVE THE LOWER PANEL BENEATH THE GLOVE BOX. YOULL SEE THE RELAYS ON THE DOOR SIDE OF THAT AREA NEAR THE CROSS BRACE THAT SUPPORTS THE GLOVEBOX AND THE PANEL YOU JUST REMOVED.

User Avatar

Remove the liftgate inner trim panel.Remove the liftgate inner trim panel.

User Avatar

Remove the following...1 screw below door panel light...1 screw by trunk release button...1 screw in door panel compartment...1 screw inside top door panel above vent hole...2 screws in door handle behind covers...remove power seat and window control by pulling up on the tapered end with a screwdriver...pull bottom of door panel out and lift up...unplug the usual...I think the speakers are 5 X 7...when replacing or upgrading buy speakers with high RMS not watts...

User Avatar

First, take the two screws out of the inside door handle. The screws are covered by a plastic cap on each side of the handle. Take a flat screw driver or something equivalent to remove the caps and then remove the screws with a number two Philip head. Be advised that all of the screws that will have to be removed will be with a number two Philips. There are two other screws to remove after that. The next screw is under the opening handle. When you remove the screw, pull the opening handle to the open position to remove the plastic covering. The last screw is under the air flow vent on the top far left of the inside of the door. This is where the hard part gets in. Take that same flat head screw driver that you popped the pull handles of wit to pry the bottom of the door panel loose. Both the left and the right side of the panel will have to be done the same. The door panel are held with fasteners and if they break, be sure to replace the fasteners wit new ones when you attempt to reinstall the panel. Once the right, left, and bottom of the panel is loose, you should be able to lift the panel off of the door by pulling straight up.


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.