answersLogoWhite

0

  • Clutches and Flywheels
  • Ford Ranger
  • Water Pumps
  • Chevy Cheyenne

How do you remove the fan bolt from the water pump on a 94 Ford Ranger 6.0?

User Avatar

Wiki User

βˆ™ 2015-07-15 21:03:18

Best Answer
Copy

Your auto parts store usually has a kit you can rent that has a wrench and spanner that allows you to hold the pulley while you loosen the nut. Quick and easy. Just ask for a water pump pulley removal kit.

2015-07-15 21:03:18
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Your Answer

Loading...

Related Questions

Wheel bolt pattern 2002 Ford Ranger?

what is the lug/bolt pattern for a 2000 ford ranger?


What are the bolt patterns for a 2000 Ford Ranger?

bolt pattern for 2000 ford ranger & ft pounds


How do you remove 94 Ford Ranger alternator pulley?

Use an impact wrench to remove center bolt and pulley should slide off


What is the Torque setting for alternator on a Ford Ranger?

The Ford Ranger alternator bolt torque specification is dependent upon the year of the Ford Ranger. In general, the alternator bolt torque specification is 45 pounds.


How do you replace Shift Lever tube Bushing ford ranger 98?

If it is a manual Ford Ranger 98, simply open the boot at the base, remove the nut that is on the bolt, put the nut on the other side and tighten it there instead. Then the bolt will be forced out of the shaft.


Will a 1990 Ford Ranger 4.0L bolt in to your 1989 Ford Ranger?

no you can't wire it up and get it to run.


How do you remove the spare tire from under a 1995 ford ranger?

undo the bolt in the middle of the tire and pull the barcket down


What are the torque specs for the water pump on a 1999 ford ranger 3.0?

The 1999 Ford Ranger 3.0 liter water pump bolt torque specifications are 40 pounds. You do not want to torque the bolts to hard or they will break.


How do you remove the spare tire from a 1997 ford ranger?

use a socket to loosen the bolt holding it up and pull the bracket down


Removal of spare tire from Ford Ranger XLT?

You will need a ratchet and a socket to remove it. You get under the rear of the truck and you will see the bolt and bracket holding the tire in place. Remove the bolt and the bracket hinges downward.


2007 Ford Ranger bolt pattern?

bolt pattern is 5 x 4.5"


Are the bold patterns the same for a 1992 Ford Ranger and a 1996 F150?

Bolt Patterns are different ; 1992 Ford Ranger = Bolt Pattern: 5-114 1996 F150 = Bolt Pattern: 5-139


What is the wheel bolt pattern on a 2008 ford ranger?

5X114.3


How do you remove the spare tire on a 2002 ford ranger?

You will need a ratchet and a socket to remove it. You get under the rear of the truck and you will see the bolt and bracket holding the tire in place. Remove the bolt and the bracket hinges downward. You will need a ratchet and a socket to remove it. You get under the rear of the truck and you will see the bolt and bracket holding the tire in place. Remove the bolt and the bracket hinges downward.


How do you replace the center arm rest for a 1999 Ford Ranger?

SLEDGE HAMMER. That's how I did it. Then I found the bolt. You must first remove the plastic insert. The pivot bolt is toward the rear of the beast.


What is the wheel bolt pattern size for a 2001 Ford Ranger?

5x114.3


What is the bolt pattern on a 1975 Ford F100 Ranger?

typically 5X139.7


How do you change a gem module in a 1996 ford ranger?

remove trim around radio, remove radio, remove the airvent extension, computer is mounted on the side of the instrument panel. 1 bolt, and 4 connectors


What is the lug pattern for a 1997 ford ranger?

The 1997 Ford Ranger pickup truck uses a five bolt lug patterns. The five bolt lug pattern is used in most of Ford's pickup trucks.


Would a 1995 Ford Ranger transmission work in a 1998 Ford Mustang 6 cylinder?

It is possible, but it is most likely not a bolt-for-bolt swap.


What is the bolt pattern on a ford ranger rim?

5 on 4.5 as were most Ford and Dodge RWD vehicles.


What size mounting bolt on a 1987 Ford Ranger?

To receive a correct answer more information will be needed: (mounting bolt for ???).


Will the manual trans from a 4-cylinder Ford Ranger bolt up to the bell housing of a 6-cylinder Ford Ranger?

I am converting a ford ranger automatic (a4ld) transmission 4wd to a 5 speed manual from a 4 cylinder ford ranger. Will it work. What is needed?


What is the bolt pattern on a 1987 ford ranger rims?

5x4.25 like the mustang


What is the wheel bolt pattern for a 1999 ford ranger 4X4?

5 by 4.5