0
How do you remove the four large torque converter nuts in a ford focus 2000?
Wiki User
∙ 15y ago
remove the exhaust pipe from under the motor. then between the motor and transmission you will see a plate with 2 bolts , take them out and then the cover will come off . then turn the motor with flat head screw driver to flywheel until the the nuts are in that opening and unbolt.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you install the four large torque converter nuts in a ford focus 2005 ZX4?
Ratchet wrenches work well.
How do you remove the torque converter on a 2006 Chevrolet HHR?
you gotta remove the trans and it is the first thing you see inside the open end of the trans - a large round donut looking steel thing with a short shaft in the middle with a hole in it. You have to loosen three bolts that connect the torque conv to the flywheel it is easiest to loosen these three bolts through the hole left by removing the starter first
How do you rotate motor on a 92 explorer to remove torque converter bolts?
use a large flat screw driver and one tooth at a time turn the engine until you reach the next bolts. You may need to remove to spark plugs to allow the cyl pressure to be releaved hope this helps B
How do you drain tranny fluid out of a 2001 s-10?
Asuming this is an automatic transmission, Using a large wide drain pan, loosen all the bolts holding the trans pan up, allow some fluid to drain, remove bolts, remove pan. Aprox 4 qts will drain out. This will be all the fluid you can drain out which is less than half of the fluid the trans holds. A large portion of the fluid is still in the torque converter.
How do you get to the torque converter to flywheel bolts on a 1998 Chevy s-10 pickup 4.3 v-6 with 4l60e trans?
Remove the transmission cover plate, under the vehicle, that will expose the flywheel, you should be able to see the bolts form there, to remove get a ratchet with a long handle and the correct socket, you will have to pin the flywheel with a large flat blade screwdriver to keep it from turning on you while you loosen the bolts, reassemble in reverse order
What is the transmission fluid capacity for a 1974 Chevy Nova?
The transmission fluid capacity of a 1974 Chevy Nova is 10 quarts. This includes a large amount of fluid which is stored in the transmission and torque converter which is never fully drained.
How does a large force produce a small torque and it is possible for a small force to produce a large torque?
Torque is the product of (force) x (distance from the center of rotation).So with a distance from the center that's large enough or small enough,any force can produce as much or as little torque as you want.
How it is possible for a large force to produce only a small or even zero torque?
if large force is applied keeping the minimum moment arm then it produces a very small torque or even no torque.
What are the large and small knobs on the side of a microscope?
The knobs on the side of a microscope are the focus knobs. The large one is the course focus, and the smaller one is the fine focus.
What was the Bessemer steel converter?
The Bessemer steel converter is a large container in which molten iron is converted into steel. The Bessemer steel converter was invented by Henry Bessemer in 1856.
How do you remove an Automatic transmission in a 1983 Chevy Camaro?
Disconnect negative battery cableRemove the air cleaner labeling all hoses as they are disconnectedDisconnect the tv cable at the carburetor/TBI unitRemove the trans dipstick from the tubeRemove the upper bolt retaining the dipstick tube and separate the tube from the transmissionRaise and support the car on jackstandsRemove the driveshaftDisconnect the speedometer cable at the transmissionDisconnect the TCC wire connector at the transmissionRemove the torque arm to transmission bracket bolts.CAUTION rear spring force will cause the torque arm to move toward the floorpan when arm is disconnected place a wooden block between the torque arm and floorpanLoosen the rear torque arm bolts and pull the front of the arm free of the bracketRemove the catalytic converter/exhaust pipe bracket at the rear of transRemove the support bracket bolts at the inspection coverRemove the bolts retaining the inspection cover and remove the coverRemove the now exposed converter to driveplate bolts it will be necessary to turn the crankshaft to bring each bolt into view use a wrench on the large bolt at the front of the crankshaft.Mark the relative position of the converter and driveplate with a scribe so they can be reinstalled in the same position.Engage a large screwdriver in the teeth of the driveplate to prevent movement as the bolts are loosenedUse a floorjack and a piece of wood placed between the jack and the trans support the trans and remove the rear mount boltRemove the crossmemeber bolts and the crossmemberLower the transmission as far as possible without causing the engine or trans to contact the firewall then disconect the tv cable assembly and the oil cooler lines at the transSupport the engine at the oil pan rail with a jack and remove the transmission to engine bolts.The upper bolts should be removed firstMove the trans to the rear and down.If necessary carefully pry it free from the driveplate keep the rear of the trans down at all times to prevent the converter from falling out.The converter can be held in place with a strap
where can I get a good voltage converter ?
If you are looking for a consumer travel voltage converter, typically any place that sells luggage will sell a converter. Brookstone also sells a good selection of these. If you are looking for a power-conditionings voltage converter for a large piece of equipment, voltageconverters.com has a good selection of converters that are suitable for supporting large equipment.
