Drain the water from your 1988 Chevy cooling system. Remove the heater core water supply hoses. Remove the heater core retaining bolts. The heater core will come out.
The easiest and quickest way to change the heater core in your 1988 GMC Jimmy is to remove the water from the cooling system. Remove the water lines from the heater core. Remove the heater core retaining bolts. Reverse the process to install the new heater core.
if its like the 1988 u would have to remove the glove compartment and it should be right behind that, ask a mechanic to make sure ,
To replace a 1988 Dakota heater core, first discharge the A/C. Then remove the lower instrument panel before removing the heater box unit.
First remove the right front speaker and cover then remove the top bolts in the heater box and the remove the heater hoses out front in the spare tire compartment. Then remove the two straps holding the heater core in place. Reverse order for installation.
The dash has to be removed to gain access to the heater box. The heater box then comes out and is split open to replace the core.
Inside of the car. Remove the glove box.
Drain the water from your Dodge Ram truck cooling system. Remove the water lines from the heater core. Remove the heater core retaining bolts. Reverse the process to install the new heater core.
A "heater" or a "heater core"?
under your driver side dash. you may have to remove the kik panel
yes I just instaled a 1990 in my 1988
Remove the positive battery cable from your 1988 Chevrolet 1500 pickup truck battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install your new starter.
Chevrolet Tracker was created in 1988.
The 1988 Chevy G 20 Van heater core can be found behind the passenger side kick plate. You will need to remove the kick plate in order to access the heater core.
You have to pull the dash and all the lower fascia, then remove the box that houses the heater core. Take the clamps off the heater hoses from the engine compartment side of the firewall and disconnect the heater hoses. Disconnect the bracket that holds the heater core in place from the inside of the passenger compartment (if present.) Carefully remove the heater core and discard it. Install a new heater core reversing the above steps.
you have to remove the dash and every thing attached to it. Is it the same for a 1988 Mazda 929?
You will need to remove the inside door panel of your 1988 Chevrolet Blazer S 10. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install the new door handle.
I was about to assume this was a typo and the question is really about the heater core ... But decided they might be asking about the block heater cord(??)If it's the CORE you're looking for, see "Related Questions" below
On all chevys that year 1979-1988 It's Not Fun. Step 1. Remove heater hoses from core under hood. 2. Remove glove box door inside. 3. Take off all 5 heater mounting nuts under the hood. 4.Remove defroster hood on front of heater inside . 5 Gently pull heater unit back and down. 6. Remove all control cables from heater and mark them. 7. Then you can take heater core out of heater casing by removing 4 srews from case where core is. 8. remove front and back retainer straps from core. Reverse to put it back in.
Easiest way: There isn't one. Remove whole dashboard.Upper passenger floorboard the core is located. Remove the in and out hoses in the engine compartment. Once dash is removed, which is a pain. The heater core will be exposed for removal.
Take the glove box out. Look in behind. Have fun -- it's not a nice job.
remove steering column, pull back dash to passenger front seat, you do not have to dis-assemble entire dash panel. You can access plenum (heater box)this way.
I have a 1987 ford bronco and I changed the heater core in about 15 minutes. All you have to do is remove glove box and there is a panel with a few screws around it. and there you go.