Begin by training the water from your 1997 Pontiac Bonneville cooling system. Remove the heater core water supply hoses. Remove the heater core retaining bolts. Reverse the process to install the new heater core.
Take both heater hoses off at the heater and the hose running from the front, attach it to the rear of the engine.
First remove the right front speaker and cover then remove the top bolts in the heater box and the remove the heater hoses out front in the spare tire compartment. Then remove the two straps holding the heater core in place. Reverse order for installation.
Any parts store will have them or can order them for you.
how do you remove the heater core and hoses from 1996 Chevy sub 5.7 K1500
Remove both heater hoses from inlet & outlet of heater core. Connect these hoses together.
I have antifreeze coming out of the bottom of my 1995 Pontiac grand am in the middle of the frame just below my front end is this from the heater core?
Remove the water supply hoses from your 1997 Nissan heater core. Remove the heater core retaining bolts. The heater core will come out.
remove panel cover in middle of car under dash where the heater core hoses are at that go through the firewall under the hood, this is where the heater core will be located at inside the car start removing screws, until covers come off remove the hoses first though i have to replace the heater core in a 93 Bonneville tomorrow good luck
you do it from the inside of the car, behind the dashboard
To change the heater core on a Pontiac Aztek, locate the heater core on the firewall, passenger side of the vehicle. Remove bolts on the firewall and the clamps on the hoses. Take out the old heater core and replace with new. Tighten bolts and hose clamps. Then check to make sure the radiator is full of antifreeze.
remove the four nuts in the engine bay on the heater box near where the heater core hoses enter. Drain coolant remove the hoses and pull the heater box out from the inside of the car. Remove clips holding heater core, than put your new one in.
Remove the water supply hoses from your 1993 Chevy Corvette heater core. Some water will drain out of the hoses and the heater core. Remove the heater core retaining bolts. Reverse the process to install the new heater core.
Remove the two hoses that go through the firewall to the heater. Connect these two hoses together.
windshield leaking heater core or heater core hoses.
Usually at the firewall either passenger side or middle follow the heater hoses
Drain the radiator..Disconnect the heater water hoses from the heater core.Disengage the stops and lower the glove compartment door.Remove the electronic blend door actuator and bracket assembly.Remove the screws.Remove the heater core cover.Remove the heater core.Follow the removal procedure in reverse order......
There are hoses in the engine compartment that go to the heater core. You can remove the intake and out going hoses from the heater core. You have to either block off these hoses or connect them together, depending on the make of the vehicle.
Remove the kick plate on the passenger side of the passenger cabin. Remove the heater core water supply hoses. Remove the heater core retaining bolts.
Simple, take the inlet and outlet hoses going to and from the heater core and connect them together.
-remove front seats-remove steering column-remove entire dash-remove heater hoses from engine side of firewall/bulkhead-remove A/C hoses from engine side of firewall/bulkhead-remove nuts holding heater / A/C box (on engine side of firewall/bulkhead)-remove heater / A/C box from cab side of firewall/bulkhead-remove top of heater / A/C box.-replace heater core
The heater hoses connect the block, radiator, heater core, and waterpump. To replace, drain the radiator and catch the anti-freeze for recycling. Remove the hoses and put on new hoses. It is kind of nasty but not very difficult.
Remove the water supply hoses from your heater core. Remove the heater core retaining bolts. Reverse the process to install your new heater core.
2 - inlet & outlet
Drain the water from your 1988 Chevy cooling system. Remove the heater core water supply hoses. Remove the heater core retaining bolts. The heater core will come out.