0
Before you remove CV axle from tranny, be prepared to catch tranny fluid. Use a pry bar to separate it from tranny. When installing new part, place a piece of wood on end of outer CV joint before striking with hammer (with it installed in steering knuckle).
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you replace a cv axel in a 99 Hyundai elantra?
* Remove the wheel cover or hub cap.Remove the cotter pin * Break the hub nut loose with a socket and large breaker bar NOTE: If the socket will not fit through the opening in the center of the wheel install the spare * Loosen the lug nuts raise and support car securely on jackstands.Remove the wheel and drain the transaxle lubricant. * Detach the stabilizer bar link(s) from the control arm(s) * Separate the lower control arm from the steering knuckle.Now remove the driveaxle/hub nut * Swing the knuckle/hub assembly out (away from the car) until the end of the driveaxle is free of the hub.If the driveaxle splines stick in the hub tap on the end of the driveaxle with aplastic hammer.Carefully pry the inner CV joint from the transaxle using a large screwdriver or prybar positioned between the CV joint housing and the transaxle housing.Support the outer end of the driveaxle with a piece of wire to avoid unnecessary strain on the inner CV joint * Support the CV joints and carefully remove the driveaxle from the vehicle
How do you replace the CV axle on a 97 elantra?
* Remove the wheel cover or hub cap.Remove the cotter pin * Break the hub nut loose with a socket and large breaker bar NOTE: If the socket will not fit through the opening in the center of the wheel install the spare * Loosen the lug nuts raise and support car securely on jackstands.Remove the wheel and drain the transaxle lubricant. * Detach the stabilizer bar link(s) from the control arm(s) * Separate the lower control arm from the steering knuckle.Now remove the driveaxle/hub nut * Swing the knuckle/hub assembly out (away from the car) until the end of the driveaxle is free of the hub.If the driveaxle splines stick in the hub tap on the end of the driveaxle with aplastic hammer.Carefully pry the inner CV joint from the transaxle using a large screwdriver or prybar positioned between the CV joint housing and the transaxle housing.Support the outer end of the driveaxle with a piece of wire to avoid unnecessary strain on the inner CV joint * Support the CV joints and carefully remove the driveaxle from the vehicle
How do you replace cv joint on a 1997 dodge grand caravan?
Remove wheel and brake caliper, remove caliper frame and ABS cable.Separate tie rod end and ball joint from steering knuckle. Remove hub nut and pull knuckle away from outer cv joint. Insert a thin pry bar between cv inner and transaxle case and jerk it to loosen cv joint. Re-install in reverse order.
How do you remove a drive shaft from a ninety nine elantra?
1.Remove the wheel cover or hub cap.Remove the cotter pin 2.Break the hub nut loose with a socket and large breaker bar 3.Loosen the wheel lug nuts,Raise the vehicle and support it securely on jackstands.Remove the wheel.Drain transaxle lubricant 4.Detach the stabilizer bar link(s)from the control arm(s) 5.Separate the lower control arm from the steering knuckle.Now remove the driveaxle/hub nut 6.Swing the knuckle/hub assembly out (away from vehicle) until end of the driveaxle is free from hub.If the driveaxle splines stick in the hub,tap on the end of the driveaxle with a plastic hammer.Carefully pry the inner CV joint from the transaxle using large screwdriver or prybar positioned between the CV joint housing and the transaxle housing support the outer end of the driveaxle with a piece of wire to avoid unnecessary strain on the inner CV joint. 7.Support the Cv joints and carefully remove the driveaxle from the vehicle
Can you remove a transmission on a 2001 Eclipse without removing the right Transaxle?
The car has only one transaxle, AKA transmission, then no, you cannot remove the tranny without removing the tranny. If you mean without removing CV Axle or drive axle or Axle shaft or CV shaft (same thing) then the answer is still no. You cannot remove the transaxle without removing the drive axle/CV shaft.
CV axles remove 2000 sonata?
how does the cv axle on the driver side removed it wont come out of the transaxle 4cly auto 2002 sonata
How do you remove the transaxle nut so i can get to th cv boot and what tool do i need?
You need an impact wrench
How do you replace cv joint on a Mazda mx-3?
To replace your CV joint you will have to slacken your hub nut before jacking and removing the wheel. Remove hub nut, remove both bolts on the bottom of the shocky, remove bottom ball joint bolt. You should have enough play to remove your shaft from the hub. Remove CV boot, CV joint should just pull off shaft. I made the mistake of buying and fitting a full drive shaft unnecessarily.
How do you remove the half shaft on a 1995 fotd escort wagon?
Left half shaft removal and right halfshaft removal. 1. Raise the car on stands and remove the wheel and tire. 2. Use a hammer and punch to raise the staked part of the nut. 3. Remove the nut from the driveaxle. 4. Remove the splash shield from the side you are working on. 5. Tap the end of the driveaxle with a hammer and punch to free it from the hub. 6. Remove the pinchbolt from the bottom of the lower ball joint. 7. Turn the steering wheel all the way toward the side you are removing the driveaxle from. 8. Pull the hub and knuckle out while you push the driveaxle out of the hub. 9. Swivel the end of the driveaxle forward and support it with a piece of wire so the ininer CV joint isn't damaged. 10. Support the engine with a block of wood positioned beneath the oil pan. 11. Remove the transaxle crossmember. 12. Place a drain pan under the transaxle to catch the fluid. 13. Insert a praybar between the inner CV joint and the transaxle case. Pry the driveaxle out of the transaxle. Be careful not to damage the CV joint, its boot, the transaxle case or the oil seal. 14. If both driveaxles are being removed insert a snug fitting wooden dowel into each of the differential side gears to hold them in place. A broom handle that has been cut off will work for this. a
How do you change the front wheel bearings in a 2003 Monte Carlo?
You have to replace the entire hub assembly, the wheel bearings are inside of it. Jack up car, remove tire, remove brake caliper and rotor, remove hub nut on cv axle, remove bottom ball joint nut(use pickle fork tool to remove ball joint from hub), tap cv shaft loose of hub, unbolt strut from hub, unplug abs wire, and replace hub assembly. Reverse steps to reassemble.
How do you remove a passenger side cv shaft on a 1997 mercury villager?
It is the same basic procedure as thee left side with one exception. Remove the cotter pin and retainer from the stub shaft. Break the hub nut loose with a socket and large breaker bar. Loosen the lug nuts, raise the vehicle and support it on jack stands. Detach the lower ball joint from the steering knuckle. Disconnect the stabilizer bar link from the lower control arm. Pry the lower control arm down and separate the ball joint from the steering knuckle. Remove the the brake caliper and suspend it on a wire. Remove the brake disc. Remove the drive axle hub nut and washer.Using a a two-jaw puller, press the stub shaft until it breaks free. To remove the right side drive axle, mark the relationship between the the axle center bearing retainer and bracket and remove the axle bearing retainer bolts. Position a large pry bar behind the flange of the inner CV joint and pry sharply to free the circlip on the inner CV joint stub shaft from the transaxle. Pull the strut away from the vehicle and separate the stub from the hub. Remove the drive axle from the vehicle. When reinstalling the drive axle. support the CV joints. NOTE: There is no circlip on the right side inner CV joint stub shaft.
How do you remove driver side front cv joint on 96 geo prizm?
1) Remove the cotterpin for the CV shaft axle nut and loosen nut 2)Jack the front of the vehicle 3) Place a jack stand under to secure the raised vehicle 4)Remove the tire 4) Remove the tie rod cotterpin & nut. Use a gear puller to loosen the tie rod joint (or use a tie rod joint splitter if you plan on replacing the tie rod ball joint). 5) Remove the axle nut 6) Remove the 2 nuts and 1 bolt for the lower ball joint. 7) Use your puller to free the axle shaft from the wheel hub. and separate the hub from the CV shaft 8) Place a pry bar between the CV shaft and transaxle and pry the CV shaft loose. 9) Remove the shaft TO INSTALL: IMPORTANT-DO NOT BEND THE CV SHAFT JOINTS. DO NOT PULL ON THE SHAFT JOINTS. DO NOT USE A HAMMER TO INSTALL 1) Lube the CV shaft (tranaxle side) spline. Insert the shaft with the split ring retainer opening at 6 o'clock. Firmly press the shaft into the transaxle 2) Lube the wheel hub shaft spline and place wheel hub over the shaft. 3) Reinstall everything removed in removal steps. Torque each to Mfg. specs. 4) Have a beer to celebrate completion! Lube the
