0
How do you remove the intake plenum on a Mazda 6-cylinder 3.0L?
Wiki User
∙ 12y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How can I replace the Spark Plugs for a Mazda MPV 2003?
You have to remove the intake plenum air chamber to get to the 3 plugs against the firewall. It requires to buy intake plenum gaskets and go ahead and replace the PCV hose on the back of the plenum. Need to get from the dealer. Gaskets also from dealer.
Where are the fuel injectors on 1988 Mazda rx7?
there's four injectors you have two primary and two secondary , the primary injectors are on the top of engine very visible but the secondary you would have to remove upper intake plenum to get to them ...
Where is the PCV valve located on a 2005 Mazda 6i with a 2.3 liter?
It is located under the Intake Manifold. You must remove the intake manifold to get to it.
How do you install a spark plug on a Mazda mpv 2002?
MPVclub.com has a somewhat detailed description on how to do it. If you remove the plastic you will expose three of the six. Then you have to remove the plenum/manifold. Check out the details on the website. Hope this helps.
Where is EGR valve for 2003 Mazda Protege?
The EGR is right under the throttle body. It has like a little black top. You have to remove the intake hose to see it. Its a pain to get to and remove.
How do you replace an ignition coil on a 2003 Mazda MPV?
Well, depends if your talking cylinders 4,5,6 which are in the front or 1,2,3 under intake. Front 4,5,6 easy; remove crankcase hose from front valve cover, slip it to the side loosely, remove 3 8mm hold down bolts for plastic dressing/cover hiding coil packs and intake plenum. Remove cover, locate coil packs, disconnect electrical connector by squeezing and pulling firmly, then remove 8mm bolt securing coil. Simply re install new one in reverse. Cylinders 1,2,3 must remove air intake box and hose and all electrical connections in the immediate area of that. Remove EGR valve-2 12mm bolts- and connector, careful not to drop gasket found between intake and valve. Remove 1, 8mm bolt securing intake to block found by egr valve, also remove on passenger side of compartment the 2, 8mm bolts securing the manifold pressure sensor from the side of intake. See power steering pressure hose clamp bolted to intake-rermove and also 1 8mm bolt in rear securing bracket to intake. Loosen and remove 6 8mm bolts securing upper plenum, remove plenum and watch if any additional parts drag against each other and adjust as needed. Slide manifold to side only half way; enough to see coils and same procedure as fronts. re-assemble. Install egr valve first that way its not so tight o install after. Secure bracket bolts and sensors/switches,air box, oh and remove battery. Will make more room for service.
Where is the fuel pressure regulator located on a 1995 Mazda 929?
It is located behind the center of the plenum. Which some would consider the intake on this particular car. It is the little round thing up close the center of the fire wall on the car. It is kind of hard to see. It is easier to find if you follow the fuel hose behind the intake.
Where is the oil filter in a 1996 Mazda Miata?
Underneath the intake manifold. If you remove the front right wheel, you'll see it up behind the fender. For owners with thinner arms, you could remove the oil filter from the engine bay, reaching under the intake manifold.
Torque on the air intake manifold of a Mazda 2002 tribute?
what is the tork for the intake(bolt 8mm) v6 3l 2001 Mazda tribute es
How do you change the coils on a Mazda RX8?
remove the intake up to the throttle body. after that you should be able to see the coils on the drivers side of the engine. remove the bolt and replace. don't mix the ignition wires.
How do you change spark plug on a mazda tribute 2004?
Disconnect the battery, remove the intake manifold, remove the spark plug boot covers and cables, and remove the old spark plugs. Put in the new spark plugs, attach the spark plug boot covers and cables, replace the intake manifold and connect the battery.
Is the Intake manifold of a Mazda 6 2.3 the same as the one of the 2.3 Mazda 6?
yes
