Brake Pads and Rotors
Isuzu Trucks
Honda Civic CX
Ford Escort LX

How do you remove the rear brake drum on a 1995 Isuzu truck?

707172

Top Answer
User Avatar
Wiki User
2015-07-15 20:04:22
2015-07-15 20:04:22

pull the wheels off and on the studs there is two loskrings that hold the drum on during assembily.remove these and the drum should slide off. if not go to the back of the drum and at the lower part of the backing plate you will see a rubber gromet. pull it out and use a brake spoon to adjust the shoes enough to slide the drum off.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

You will need to remove the tire and wheel from your 1995 Chevy Cheyenne. Remove the brake assembly. Tap on the rotor with a hammer or mallet. The brake rotor will slide off. Reverse the process to install the new brake rotor.

User Avatar

Remove the tire and wheel from your 1995 Chevy. Remove the brake assembly. Tap on the brake rotor with a mallet or hammer. The brake rotor will slide off.

User Avatar

Do the following to remove the brake drum on 1995 Isuzu Pickup. - Remove wheel from the brake drum- Remove the Philips screw that holds the brake drum to the axle plate. The brake drum is now free to be removed but is usually stuck to the lug bolts.- spray penetrating oil on the lug nuts (be sure to put card board below wheel to catch the oil that will run off.- Use a plastic hammer and hammer the drum off the axle plate. - An alternate way is to place a 2 x 4 across the top of the lug nuts and use two c-clamps to pry the drum off the lug nuts.

User Avatar

Remove the tire and wheel from your 1995 Chevrolet K 3500. Remove the front brake assembly. Tap on the brake rotor with a hammer or mallet until it becomes loose. Slide the brake rotor off.

User Avatar

Remove clamp that holds the rode on back of brake booster that hooks to the brake peadle. Then remove the two nuts on the brake booster that holds the mastercylender on the in the inside of truck remove the 4 nuts/bolts that hold the brake booster on then remove brake booster then replace with new one.... P.s. Make sure u pump brakes b4 u move vehicle........ U shouldnt have to bleed brakes unless u undo mastercylender

User Avatar

Remove the wheels from your 1995 Toyota Camry. Remove the brake pads by removing the brake pad Springs. Tap on the brake drum with a hammer or mallet. Slide the brake drums off. Reverse the process to install the new brake drums and shoes.

User Avatar

Remove rear wheels Loosen brake lines - but do not toally remove Loosen and remove 2 caliper mounting bolts remove brake line

User Avatar

Begin by removing the brake lines from your 1995 GMC Jimmy brake booster. Remove the brake booster retaining bolts. Reverse the process to install your new brake booster.

User Avatar

Check at the upper end of the brake pedal undeer dash area

User Avatar

Lift the car, remove the tire, remove the brake shoe/caliper and remove the old brake pad. Put in the new brake pad, replace the brake shoe/caliper, replace the tire, and lower the car.

User Avatar

located at the upper end of the brake pedal under dash area

User Avatar

two bolts in the steering knuckle and the brake line are all that attach to the brake caliper

User Avatar

The speaker covers are held in with a screw, remove it and tilt it out away from where the screw was. then remove the screws holding the speaker in and remove the speaker.

User Avatar

Lift the vehicle with a car jack, remove the tire, remove the brake shoe/caliper and remove the old brake pad. Next, put in the new brake pad, replace the brake shoe/caliper, replace the car tire, and lower the car to the ground.

User Avatar

where is the pcv valve located on a 1995 Isuzu rodeo v6 3.2l

User Avatar

You will need to remove the water lines from your 1995 Dodge Dakota truck heater core. Remove the heater core retaining bolts. Reverse the process to install the new heater core.

User Avatar

A 1959 truck has a mechanical clutch. A 1995 truck uses Dot 3 brake fluid for the hydraulic control.

User Avatar

you remove plastic red/white cover with 2 screws and remove bulbs.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.