I have a 92 Cavi, So there shouldn't be much difference, after removing the screws, you have to pop off the window crank, then lift up on the panel and it should pop off.....If you have electric windows, Im stuck, lol.
I have the same model. You take all the screws around it out...pull out the panel where the tree's are located...then once the entire thing is loose (meaning nothing holding it on that you can see) lift up on the door panel. You will probably have to unplug the wires for the power locks and windows after your done...its not difficult. The only difficult part is putting it back on. You have to plug the wires back in..... then put it back on without the black strip that separates the window from the panel..then you try to put it back in and once the panel is hanging on the door you slam down from the top of the panel. Then just screw everything in. However before you slam down on it...make sure the metal clips at the tip top of the panel are aligned with the door.
Remove the inside door panel of your 1997 Chevy Lumina. Remove the linkage to the window crank. Remove the window crank retaining bolts. Reverse the process to install the new window crank.
You have to remove the inside panel, where the window crank is, or would be.
Remove inside door handle and window crank handle, remove inside door panel, remove vent window and channel assembly, remove window.
There is a c-clipthat holds the crank in place,you just need to push it off and the crank comes off.
All you need is a paint can opener. Under the window crank there is a horseshoe shaped pin and you just need to snag it and pull it out. Put down the window first and do the above. Then after romoving all the screws in the door panel lift up on it until it pops off.
they make special manual window crank removal tool but you can use a screwdriver its kind of tricky though.you local parts store will have one and they will show you how to use it if you buy the tool its a breeze.and you wont damage the door panel.
You will need to remove the inside door panel of your 1977 Chevrolet blazer. Remove the window crank linkage. Remove the window crank retaining bolts. Reverse the process to install the new window crank.
behind the window crank
There is a c clip holding the window crank on. The tool slides behind the crank and opens the clip.
Remove the inside door panel. Remove the Allen screw from the window crank linkage. The window crank handles should come off.
You have to have a window crank remover, this tool looks like a U on a stick, and you slide this tool in between the the crank and the door panel and trip the lock pin, then the crank will pull off.
You need a door handle removal tool. Go to any auto parts store and buy one. They're about $5
Most chevys have a horseshoe shaped clip on the window crank. There is a special tool to remove it , but I just push them off with a small screw driver, or hook the back with a dental tool
Pry the screwdriver between the door panel and the window crank base. Remove the metal clip slowly and carefully. Pull the base of crank to remove it.
There is a horseshoe-shaped metal clip behind the window crank. You must ply the clip out from behind the crank in order to release the crank itself. I would advise you to remove the crank before unscrewing any parts to the door (the process can be very difficult and this will save time). Some auto stores sell cheap removal kits for this.
there is a clip on the handle you have have the knob faceing upward and use a flashlight and a butter knife to remove. The clip is u shaped.
To remove the window knob,you need to purchase a tool at any auto parts store, you would then slide the tool behind the window crank and simply push out the clip that holds the window lever in place.
Window cranks are easy to remove. Go to the local auto parts store, and ask for a window crank removal too. Slip it in behind the crank until it comes free.
How to Remove or Install Car Window Crank Handles check related link below
You need to remove the window hand crank with a window hand crank removal tool.
To replace the window crank handle on the 1993 Geo Prism, first remove the interior door panel. Then, access the screw that holds the window crank in place and remove it. You can then remove the handle itself.
Pull out the U-clip located on the base of the window crank.
General Chevy info, remove door hande bezel, remove armrest, remove window crank if it has manual windows.(there is a clip on the crank) Start at the bottom and gently pry panel up pulling plasic clips out of holes in door. When panel is loose it will lift off of window ledge. If you have power windows or locks you will have to unplug the switches carefully
you can buy a window crank removal tool at an autoparts store that pulls the little pin off to remove it.