Not very difficult. They are held on by a variety of bolts, nuts, and push pins. The push pins have a center pin that is simply pried up with a screwdriver or pair of wire cutters (dikes). Then the push pin can be removed. When all the fasteners are removed the cover simply slides off.
# Apply parking brake,raise the vehicle and secure it # working under the vehicle,detach the fasteners securing the lower edges of the bumper cover # Working in the front wheel opening,detach the retaining screws securring the bumper cover to the inner fenderwell splash shield # Pry out the lower edge of the splash shield,then reach up behind the bumper cover and remove the bumper cover fender retaining nuts # remove the fasteners securing the upper portion of the bumper cover and pull the bumper cover assembly out and away from the vehicle. # Disconnect any electrical connections which would interfere with removal
Turn wheel in for easier access. Remove the two clips that hold the lower mud guard to the bottom of the bumper cover & move mud guard for access. Remove connector. Remove rear fog light cover by rotating counterclockwise. Remove spring clip & replace bulb. Re-install cover & connector. Verify operation. Re-install lower mud guard.
You need to remove the bumper cover in order to get at the lower bolt for the headlight assy.
there are 4 screws that fasten the headlight assembly, 2 on top that are visible when the hood in open, and 2 on the bottom that cannot be seen at this point. Start by disconnecting the hood latch pull form the latch assy. next remove the grille to expose 5 fasteners that hold the bumper cover. there are 2 more behind the lower bumper air inlets(left and right side, 1 each). next there are 4 fasteners in each wheel opening (front portion) that go into the bumper cover, now you can remove the bumper cover and expose the 2 headlight lower fasteners.
Remove the 2 clips that hold the Lower Mud Guard to the Bumper Cover & move Mud Guard aside. Remove electrical connector. Remove nuts & clips. Pull out Fog Light Assembly.....
1. If needed raise vehicle and support it on Jack stands 2. Remove the retaining screws in the wheel wells and along the upper and lower edges of the bumper cover. Remove the tail light housings. Remove the rear trim plate and pull luggage compartment trim out for access then remove the remaining bumper cover retaining screws. Remove the bumper bolts 3. On station wagons remove the rear window washer fluid reservoir for access to the bumper retaining bolts. The remaining bumper bolts are accessible from below 4. Pull the bumper and cover assembly out and away from the car
http://youtube.com/watch?v=DrCSJpbDCiI follow the lower (on the passenger side) raidiator tube down to the engine, remove the thermostat cover (2 bolts) you may have to drain your radiator fluid
# Remove the front bumper cover # Remove the upper headlight housing mounting bolt and pushpin # Remove the lower headlight housing mounting bolts # Pull out the headlight housing assembly and disconnect the electrical connector
If it is in the same place as the 1995 (in which I think it is) it is inside the lower right front bumper (fascia). You have to take the lower plastic cover (on lower underside front bumper)off in front of wheel to get access. Real pain in the butt to get to it because I just had to do it and replace the horn because it was bad. I think they (GM engineers) mounted it in a bad spot because I hear a lot of problems with the horn on the Cavalier/Sunfires. I relocated my up higher I hope that takes care of the problem.
your oil pump is located behind the lower timing cover. to replace you will have to drop oil pan pull crank gear off and then lower timing cover
InstructionsLift the rear of the Corolla using a floor jack. Jack up on the rear jack point behind the trunk, and place a jack stand under each of the rear pinch welds. Then lower the vehicle onto the jack stands.Pry the plastic rivets off the inner wheel liner with a flat-head screwdriver.Remove the bolts that hold the bumper to the bumper bracket and support.Pull the bumper off the bumper support.Mount the new bumper. Align the mounting holes on the back of the bumper's mounting bracket with the bumper support, and thread and tighten the bumper. Replace the plastic rivets that hold the wheel liner to the rear bumper.Remove the jack stands, and lower the car.
Inside the fuel tank. You'll need to lower the tank to replace the fuel pump.