Buy the replacement antenna from Infiniti if you can afford their inflated price, and follow the directions, it's not that hard. Essentially you undo the ring nut where the antenna goes into the car, turn the radio on so the antenna rises, and it will shove it out of the shaft, along with the ribbed nylon strip that shoves the antenna up and down. To put in the new one, simply thread the nylon strip in the same way the old one came out and have someone turn off the radio. Feed the antenna back in, and put the nut back on. Good Luck!
Begin by removing the wiring harness from the bottom of your antenna. Remove the antenna retaining nuts. Reverse the process to install your new antenna.
Go to www.antennamastsrus.com They have a replacement mast for the power antenna for $14.95 + shipping.
The antenna mast screws into the antenna mount on the fender. Unscrew the old one and crew in the new one. If you need to replace the entire antenna mount, you will need a new antenna mount assembly with antenna cable.
Buy a new mast and it just screws on.
Begin by removing the wiring harness from your Volvo antenna. Remove the antenna retaining nuts. The antenna will come off. Reverse the process to install your new antenna.
There are a lot of aftermarket antenna masts that you can get to fit your 4 runner and if you do decide to go with a fixed mast just make sure that you make sure that the wiring harness at the mast doesn't ground out on any metal. Other than that there is no problem with replacing it with a fixed mast antenna.
You would need to get a tool to remove the notched chrome piece that holds the antenna mast, or carefully use pliers to unscrew it out. After you remove that, the antenna itself is held by a 10mm bolt. to get to it you'll need to open up the trunk lining near the antenna location and remove that bolt. Then, pull the antenna far enough to disconnect the antenna wire and power. Assuming the antenna motor is still functional, you can then replace the antenna mast with a new one. Or, you can install an aftermarket rubber antenna.
the actual antenna mast can be accessed from underneath the driver-side fender flare. Hope that gets you on your way!
You can purchase an antenna mast at most auto shops like Auto Parts or Auto Zone. Many gas stations or garages will also carry the antenna mast for your car.
remove inner fender passenger side antenna mast is right there back towards door you can get a new antenna for about 56 dollars
I removed the entire power antenna assembly and could not find any way possible to separate the mast from the motor assembly. Odd, since Mitsubishi sold me an antenna mast.
You can get a new mast for the antenna from any Hyundai dealer. This happens a lot and they usually stock them. If you can get all of the old mast out, it's a rather simple procedure, although it can be tricky to get the antenna to grab the new mast. 1. Remove the nut holding the mast into the antenna (12mm I think). 2. Turn the radio on and pull the antenna mast out. There should be a round disc and a ball on the bottom. If not, you'll need to remove the antenna assembly and take the rest of the pieces out of the antenna. If the disc and ball are present, continue with step 3. 3. Push the plastic of the new antenna mast down into the antenna as far as possible. 4. Have an assistant turn off the radio while you're pushing the plastic into the antenna. 5. If the antenna does not grab onto the mast, return to step 2. Otherwise, continue with step 6. 6. Install and tighten the mast nut. 7. Turn the radio on. 8. Turn the radio off. Your mast should now be properly seated. 9.there is a plastic washer also inside that you will have to force the mast thru to get it the set in the motor ! if you cann't push thru , next step take out motor and remove the tube for antenna, you find in sitting inside make sure connect it back the same it is stting , after that replace in car, have someone turn and off radio,job done
For 300zx: may help http://www.carstereohelp.org/DoItYourselfRepair/NissanPwrAnt300zx.htm
it is threaded onto the mast you must use a small wrench on the 2 flat spots on the base of the antenna. it has right handed threads
Take it to the DEALER!!!!!!!!!!!!!!!! Not a fun job worth the money to have them do it for u . Buy it from part store the take it to the DEALER .....
the drive cord could also be broken inside the drum that holds the drive cord when the antenna is down. If that is the case, you will have to remove the cover next to the motor and remove the broken piece. I believe you can simply replace the antenna mast; eBay has one but it is for a power antenna that mounts on the passenger side. that means that the drive cord is stripped, on some cars, the mast with the drive strip alone can be replaced, on others, you have to replace the entire mast / motor assembly.
I have a 98 4runner limited and It has a power antenna, I recently replaced the mast for it and it's pretty easy to replace the antenna it self. not sure about the euro ,but I know that it's pretty easy to take off the motor (if you can get under the panel) and just replace it with a normal antenna
By mounting it on an antenna mast with the appropriate attachment bracket.
you don't.. can't replace mast.. the best thing to do is buy an aftermarket/universal power antenna or go hunt for a working one at your local junkyards.
Remove the nut, spacer and bushing that holds down the antenna on the outside car body. Then turn the radio ON. As the antenna extends out, carefully pull out the antenna mast. There will be a plastic portion with teeth at the end. Remember the direction of teeth. When you install the new antenna, the teeth will go in that direction. Insert the new antenna into the antenna housing. Make sure the antenna teeth engages the antenna motor by moving the antenna up & down. Turn the radio OFF and the antenna motor will pull the antenna back in. Reinstall the nut, spacer, bushing and you're done.
The antenna mast screws into the antenna mount on the fender. Unscrew the old one and crew in the new one. If you need to replace the entire antenna mount, you will need a new antenna mount assembly with antenna cable. Unscrew the antenna and then unscrew the antenna mount nut. Unfasten the mud guard in the wheel well enough to pull it aside and reach up to the antennae. Remove the kick panel to find where the cable enters the jeep.
THE ANTENNA MAST OPERATES ON A PLASTIC CABLE WITH TEETH ON IT. WHAT HAPPENS IS THE TEETH WEAR OUT OR THE CABLE BREAKS. TO REMOVE THE OLD CABLE REMOVE THE NUT ON TOP AND TURN RADIO ON AND PULL OUT THE OLD CABLE. TO REPLACE THE NEW ONE STICK THE CABLE IN THE HOLE, TURN THE RADIO OFF AND THE MOTOR WILL PULL THE CABLE AND ANTENNA IN AND DOWN AND REPLACE THE NUT. MAKE SURE YOU HAVE ALL OF THE OLD CABLE OUT. IF NOT YOU CAN ACCESS ANY BROKEN OFF PIECES BY REMOVING THE COVER PLATE ON THE SIDE OF THE ANTENNA MOTOR. I HOPE THIS INFORMATION HELPS.
The antenna assembly is accessed from the inside of the trunk by removing the panels. If you just want to replace the mast try this link.How_do_you_replace_an_antenna_on_a_mercedes_300EHope this helps.
A radar mast is a high platform to mount a radar antenna such as the radar has an unobstructed view.
The antenna mast is stripped.