Chevy Silverado
1995-1999 Dodge & Plymouth Neons
Mazda MX-3
Grand Prix SE

How do you replace axel shaft?

666768

Top Answer
User Avatar
Wiki User
2006-02-04 19:26:04
2006-02-04 19:26:04

This web page will give you all the info you need to preform this repair. MX-3.com/95manual

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

How do u replace the front axel on a 1997 nissan altima

User Avatar

on what year make model

User Avatar

I would say it is the left axel shaft.

User Avatar

How do you replace a 1985 Hyundai Elantra Front Axel

User Avatar

how do i remove the axel shaft off the daewoo cielo

User Avatar

i need to replace the flex shaft in my weedeater. how do i do it?

User Avatar

first jack the chaulk the back wheels, then jack up the front end and place it on jack stands, next remove the bolts from the transmission pan and drain the tranny fluid, then proceed to remove the wheel on the side that needs relacing, separate the ball joint and pull the axel shaft out of the transmission, replace eith new axel shaft and reverse the directions to put it back together, don't forget to top up the transmission with fluid...

User Avatar

How do you replace crank shaft sensor on 2005 Chrysler 2005 300c?

User Avatar

It CAN'T be done.. Due to the design of the axel shaft and hub.

User Avatar

You REPLACE the WHOLE THING! Shaft, box and all!

User Avatar

u probaly need to replace your axel

User Avatar

Don't bother trying to replace a torn boot on a half shaft. It is quicker, easier and cheaper to replace the whole half shaft.

User Avatar

how do you replace half shaft on 2992 ford escape

User Avatar

I have a leak on my drive shaft left front 2000 cheve Blazer I would like to replace the whole unit

User Avatar

You go to the mechanic and have it done for you

User Avatar

The front axles do not have a removable shaft, you must replace axles completly.

User Avatar

You can replace that shaft with any on the market. Since that shaft came with the Ping ISI Irons and had a firm flex, since the W44 were regular, you should get a stiff shaft put in for a replacement.

User Avatar

If you mean the CV shaft itself, no, there are no special tools required, normally.

User Avatar

beleave it or not its cheaper to buy the axel than jusy the cvjoint, its not that hards to replace an axel, you need to remove the tire on that side, you will see a big nut in the center of the wheel that is your axel nut take the nut loose then you will need a hammer drive the axel thru until it is free, then you will see your strut theres 2bolts running thru the strut remove the 2 bolts after removeing the bolts from the stut pull down on the spendel and release the axel after the axel is free from the spendel grab the axel and pull it out of the trasmision not sometimes it can be hard but it will come so don't be worred and to replace the axel do everthing in revers.note after replaceing the axel the car has to be lined up you can call the parts store and they can tell you how tight the axel nut has to be. i hope this will help you

User Avatar

replace abs sensor on back axel.

User Avatar

1: disconnect the drive shaft from the rear axle. 2: disconnect the front shaft from the transmission (tedious and you need the correct size tool). 3: disassemble the front shaft from the main shaft by pulling them apart from the center or in front of the support and drop the main shaft. 5: remove bolts holding the support and drop and remove the front shaft shaft with the support still connected. 6: remove and replace the support with a wheel puller. 7: replace support with new part. 8: reassemble in reverse. CDARCO

User Avatar

take the cotter pin out of the front axel shaft then take that castle nut off and the hub should come off it might need some taping with a hammer to get it broke lose from corrossion


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.