answersLogoWhite

Top Answer
User Avatar
Wiki User
Answered 2007-02-04 13:59:17

there is one blot that attaches tension pully to block this holds the whole configuration ,on not just the pulley. buy a new one and you will see how it is manufactured, u will then know exactly where the bolt is that holds it on

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Still Have Questions?

Related Questions

How do you replace a tension pulley on a dodge truck?

The tension pulley should have a bolt that holds it on, allowing you to replace the unit.


How do you replace the idoler pulley on my Nissan 1996 200sx 1.6?

replace 1996 nissan 200sx se 1.6 tension pulley


Where is the Location of tension pulley on 2000 Ford Ranger 6-cylinder?

The tension pulley is centerline with the engine and at the very top of the belt routing.


Loosen tension on serpentine belt on a 2000 jeep Cherokee sport?

Loosen bolt in tension pulley, then loosen tension bolt. Replace belt. Tighten tension bolt. Last, tighten bolt through pulley.


Where is the tension pulley on 1995 ford windstar?

Will be the only pulley that is spring loaded and not connected to an engine component


What is a tension pulley on a Pontiac Sunfire 2.2 L Engine?

tension pulley is an automatic tensioner that keeps the serpentine belt at the proper tension it is a single pulley that is smooth (no grooves) usually turning clockwise with constant pressure loosens pulley for belt removal use caution pulley is spring loaded


How do you replace the idler pulley on a 1993 Geo Prism?

I assume you mean the idler pulley on the A/C belt. I have not replaced this particular item but it should be simple. Looking from the top of the engine compartment on the passenger side you will see the idler pulley with a mounting/locking bolt which attaches the pulley and the tension adjusting point immediately above it. Loosen the pulley locking bolt by turning counter clockwise. Relieve belt tension by turning the adjuster bolt counter clockwise. Remove the belt and pulley. Replace in the reverse order.


How do you replace a tension pulley on a 2001 Lincoln town car?

Disconnect the battery.remove the serpentine belt.Unbolt the pulley.


Can't loosen idler tension pulley on air conditioner idler pulley?

Replace the tensioner assembly as one piece.


How do you Replace starter cord on lawn mower?

How do I replace starter cord on lawn mower? Remove the engine starter cover or blower housing which contains the starter rope. Check to see if the spring is still good then just rewind the starter rope pulley to re-tension the spring. Insert the replacement rope into pulley as originally routed and let the spring wind the rope back into pulley. Then replace the starter handle. Make sure you keep tension on the starter pulley while the rope is winding.


How do you replace the idler pulley on 1992 350 engine?

Remove the old, damaged idler pulley and replace it with a new one.


How do you change idler pulley on 2001 Monte Carlo?

You can change an idler pulley on a 2001 Monte Carlo by first, removing the negative cable from the battery. Using a socket wrench, loosen the tension adjustment bolt. Slide the serpentine belt away from the pulley. Remove?æthe center bolt, and remove the pulley from the engine. Replace the pulley,?æreturn and tighten the bolts, and replace the serpentine belt.


If the tension pulley is bad on a 91 2.2 l Corsica can one just replace the pulley or must one replace the entire assembly?

Call the parts store. They will be able to tell you if the pulley is available separately or not.


How can you replace the tension pulley on a 1997 Nissan Maxima?

Loosen 13mm nut that secures tension pulley. Then loosen 13mm nut/bolt just above tensioner assembly facing upwards, to remove tension from belt. Then finally remove the three 10mm bolts holding tensioner assembly to engine block. Install in reverse order.


How do you release belt tension on a 2002 Dodge Ram?

usally' u put a 15mm or 5/8" wrench on the nut in the middle of the pulley & move the SPRING loaded Pully.IF U aren't sure wich Pulley-WATCH witch pulley Vibrates when the engine is idleing-then turn OFF the engine & replace the Belt.


How do you replace serpentine belt on 2001 impala?

Use a 15 mm socket to loosen the tension pulley... take the old belt off and replace with new belt.. then gentle pry up on the tension pulley and lock bolt back down..


How do you move the tension pulley?

There should be a "square" cut into the pulley bracket that fits either a 1/2 inch or 3/8 inch ratchet or breaker bar to allow you to remove tension from this pulley allowing you to replace the serpentine belt.


Is their a tesioner pulley on a 1994 geo prism?

Yes, it is used to adjust the tension on the A/C compressor. Looking into the engine compartment from the passenger side it is to the left of the alternator. To adjust tension you need to loosen the bolt which holds the pulley and then adjust the bolt which is directly above the pulley. Once you have proper tension tighten the pulley bolt.


How do you replace the serpentine belt tension pulley on a Buick Regal?

with a 9/16 socket and ratchet


Why would 98 ford Taurus be making noise if you changed the serpentine belt idler pulley and tension pulley?

replace the belt with a goodyear bet


Where is a tensioner pulley on a 1981 Oldsmobile omega?

When looking at the engine from the front, the tension pulley is the only wheel on the drive belt that has the belt on the inside of it. All of the other pulleys have the belt going around the top of the pulley. The tension pulley has a bolt that can be loosened and then tightened to remove the drive belt.


How do you tension serpentine belt on Nissan zd30 engine?

The zd30 has a hydraulic tensioner using an idler pulley to automatically tension the serpentine belt.


How do you replace belts on a 1995 altima?

You must first loosen the alternator, do not remove it. remove the alternator tension screws top and loosen the bottom screws DO NOT REMOVE push the alternator toward engine, for the a/c belt you must loosen the belt tension pulley and move it. replace in reverse order


How do you remove the tension pulley on the 1993 Seville 4.6L Northstar engine?

Not easily. Get a manual on your car.


Can you bypass the tension pulley on 3.3 engine for 1991 Plymouth voyager?

No I don't think so.


Still have questions?