How do you replace the blower motor resistor cavalier 97?

already exists.

Would you like to merge this question into it?

already exists as an alternate of this question.

Would you like to make it the primary and merge this question into it?

exists and is an alternate of .

Tools required:
6mm socket/ratchet
7mm socket/ratchet
Socket U-joint with extension
Step 1: Loosen and remove the 7mm bolts (3) that hold the protective panel in place beneath the glove compartment. Remove this panel.
Step 2: Disconnect the blower motor resistor's wiring harness (1).
Step 3: Loosen and remove the 6mm bolts (2) that secure the resistor to the component.
You will need to use the U-joint and an extension to reach the bolt.
Step 4: Mount the resistor to the component by tightening the 6mm bolts (2).
Step 5: Connect the resistor's wiring harness (1).
Step 6: Tighten the 7mm bolts (3) that secure the protective panel to the underside of the glove compartment.
These Part Change / Installation Instructions Apply to
05 2005, 04 2004, 03 2003, 02 2002, 01 2001, 00 2000, 99 1999, 98 1998, 97 1997, 96 1996, 95 1995 Chevrolet Cavalier, Pontiac Sunfire Blower Motor Resistor Replacement Instructions
2 people found this useful

How do you replace a blower motor resistor in a 2000 Grand Am GT?

I have a 2000 Grand Prix GT and recently replaced the blower motor resistor. First of all, there is no need to go to the dealer for the part. I purchased it for $24.95 from a local NAPA dealer. The OEM p/n is: 15304891. To replace the part, here are the steps I went through: 1) Remove the glove box. ( Full Answer )

How do you replace a 2002 Grand Prix blower motor resistor?

Step 1 remove glove box, 6 screws on the hing, compress glove boxslightly so inner track wheels are out of slots and remove. Step 2 go to google images and type blower motor for a 2003 or whatever year your Grand Prix is and you will find a good diagram ofwhat you are looking for, as well you will s ( Full Answer )

When you replace a blower motor do you have to replace the resistor module too?

Answer . \nSomething called a blower control module takes the place and is found in the hole where you would find a blower resistor, so there isn't a blower resistor in that vehicle. As far as the blower control module is concerned, the module is serviced as a unit. No part can be fixed or repla ( Full Answer )

How do you replace the blower motor resistor?

I do not know what vehicle you are referring to but I just replaced one on a 1996 Nissan Sentra because the only speed that was working on the blower motor was 'high'. Underneath the glove box was a couple of screws that came out and the new resistor was put in. Two screws and done......... Most bl ( Full Answer )

How do you replace a blower motor resistor in a 2003 Jeep Liberty?

Open your glove box and empty it out. There will be two supports on each side of the glove box, push these towards each other and the glovebox will kind of "fall out." It will still be hinged but hanging down far. You will then see a 5 wire connector going to a mount with two screws. Unscrew both of ( Full Answer )

How do you replace a blower motor resistor on a 2001 Nissan Xterra?

just behind the blower motor under the passanger side dash is a plug that is the risistor. two screws hold it in place. just remove the two screws and pull out. xterraparts.com has themm for about $19.. Xterraparts.com has pictures of the part and a diagram. In the diagram, the front arrow is poin ( Full Answer )

How do you replace a blower resistor on a 1998 Chevy cavalier?

This is a pretty simple fix. The GM part number for the Resistor is 52476725. Fits I believe 96-02 Chevrolet Cavaliers and Sunfire. Step 1: locate the blower motor under the dash on the passenger side. Step 2: To get to the resistor you need to remove the (3) screws holing up the blower. Remove the ( Full Answer )

How do you replace the blower motor resistor in a 1998 Oldsmobile Intrigue?

Answer . \nOn the passenger side under the dashboard, first remove the fire panel and unclip the light. The resistor is towards the far back in the center. There are some screws that are kinda hard to get to, but it is possible. Unclip the wires on the old resistor and remove the screws and remov ( Full Answer )

How do replace blower motor resistor on 1998 civic hatchback?

Remove your glove compartment. Look to the right side inside. Look for 2 screws, remove 2 screws. Lift up on wires, unplug wires from resistor. Plug in new resistor into wires. Screw the screws back in, reinstall glove compartment.

How do you replace a blower motor resistor?

Safety Tip: Always wear safety glasses when working on your motor. Wear otherpersonal protective equipment (PPE) when necessary, for examplelatex gloves or closed toe shoes. 1.Remove the negative battery terminal. 2.Locate the blower motor resistor on the passenger side under thedash board. It is ( Full Answer )

How do you replace the blower motor resistor on a 1998 Pontiac sunfire?

Replacing the blower motor resistor on a 2000 Pontiac Sunfire is a bugger of a job!.This project is far easier if you remove the blower fan first. You may be able to do it leaving the fan in, but you have to be an elf with very good eyesight. Tools required: 1/4" driver with a universal and a short ( Full Answer )

How do you replace the blower motor resistor pack on a Trailblazer?

1) Order the resistor pack from your local parts store or dealership. Shop around - prices vary quite a bit. Most parts stores will need to order this from their warehouse, so it might take a day or three to get the part. Dealerships will probably have it in stock, but it will cost more. I don't kno ( Full Answer )

How do you replace the blower motor resistor on a jeep 2000 Cherokee?

I just replaced mine and it took 30 minutes and the part was $35 (from Jeep dealer). Start by removing 3 philips screws that hold glove box in place (on bottom edge of glove box). Once glove box is out you can see the resistor but I couldn't get to it without removing the black panel under the glove ( Full Answer )

How do you replace a blower motor resistor on 2002 Chevy Malibu?

It is located under the glove box, way in the back of the passenger foot area. You'll need to remove 2 screws with a 7mm socket, and remove the plastic cover that covers the blower motor and another component box that I think controls the passenger airbag. After removing the plastic cover you'll nee ( Full Answer )

How do you replace the blower motor resistor on a 2000 Camry?

Remove glove box. remove the side kick panel panel (a black knob) a hex bolt to be removed and 4 Phillips screws surrounding the glove box. Its all the way in the back underneath everything. Look near the back left corner of where the glove box used to be. once reinstalling keep in mind that th ( Full Answer )

How do you replace the blower motor resistor in a 2002 cavalier?

Cavalier Blower Resister Replacement . The resister is bolted in place beside the blower motor, which is located under the dash on the passenger side of the car. It is easier to access if you recline the passenger seat and lie down on it with your head on the floor mat, looking up under the dash. ( Full Answer )

How do you replace a blower motor resistor in a 2001 Dodge Dakota?

It's actually pretty simple, anyone with a screwdriver can do it. The resistor is located under the dash on the passenger side of the truck. You have to look at it from the floor to see it. It will have a 5 wire harness connected to it and will be held in by two screws, it's about the size of a deck ( Full Answer )

How do you replace a 2000 dodge caravan blower motor resistor?

Actually, for mine, (2000 Grand Caravan A/C, 3.3L, and rear defrost, the resistor array is located in/from the engine compartment. Open the hood, to your top left, on what is almost the firewall (It is pretty much right up near the top). there is a plug with five heavy gauge wires (14/12ga), There ( Full Answer )

How do you replace a blower motor resistor in a 2000 Honda Civic?

unscrew the glove compartment - 2 bolts under the door - at the top left of the heater box there is a black plate with a cable. unplug the cable lossen the two screws and there is your resistor - easy. unscrew the glove compartment - 2 bolts under the door - at the top left of the heater box there ( Full Answer )

Where is the blower motor resistor on a 2000 Chevy cavalier?

It is located under the dash on the passenger side of the car right behind the blower motor. I am getting ready to change the one in my wife's Cavalier for the second time. There are several web sites that show pictures of the location. It is not a difficult change. The hardest thing about it is hav ( Full Answer )

How do you replace the blower motor resistor for a 1992 Crown Victoria?

When ordering a new one, be careful as there are two types, a 5 pin that came on models with automatic climate control, and a 4 pin for the standard. In either case the resistor is located under the hood, inside the airbox, right next to the dipstick and just below the heater hoses. Its held in w ( Full Answer )

How do you replace the blower motor resistor in a 1997 Ford F150?

The blower motor resistor is located under the glove box. You can locate it by finding a 4 wire connector, directly below the glove box hinge (towards the front of the truck). There are 2 screws holding it in. A mirror is helpful in replacing this, but I managed to replace it without one. You will n ( Full Answer )

How do you replace a 2003 dodge caravan blower motor resistor?

Its right in behind the glove box you cant miss it Flex both sides of the glove box bin inward near the top far enough for the rubber glove box stop bumpers to clear the sides of the glove box opening, then roll the glove box downward. The resistor is right there in the center held in with 2 screw ( Full Answer )

How do you replace a blower motor resistor on a 2005 jeep liberty?

What you need to do is open your glove box. There are two clips on each side. Push them so the glove box falls free. Then slide your glovebox to the right and the whole thing pops off. You will see the resistor right there. Take a socket loosen the bolts pop out the resistor and replace.

How do you replace the blower motor resistor in a 2006 Pontiac G6?

Only your forth speed will work when your blower resistor is gone, this is how you can tell. Under the glove compartment you will find a plastic cover that's about a foot by 1/2 foot, just pull that off. Then you will be able to see the blower and a plug that has 4 wires comming out of it. Unplug it ( Full Answer )

How do you replace a blower motor resistor in a 1997 dodge caravan?

This answer is based on repairs done on a 1997 Dodge Grand Caravan SE, with 3.3L V6, and factory installed air conditioning. Symptoms of a failed blower resistor include: blower only operates on highest setting. Please follow all standard safety precautions when servicing electrical parts. 1 ( Full Answer )

How do you replace the blower motor resistor in a 2004 ford expedition?

THIS IS FOR A MANUAL CONTROL SYSTEM Open the glove compartment door all the way (two sides squeeze in to release) and the resistor is right in front of you, embedded into the fan motor housing and is held by two screws ( 8 mm). Take two screws out and pull resistor out of fan motor housing, release ( Full Answer )

How do you replace a blower motor resistor in 2006 Chevy Trailblazer?

"Front A/C blower would stop working intermittently the back blower works "OK". Tools needed: 5.5mm and 7mm (I use 7/32 and 9/32 nut driver or small sockets), wire cuter and some electrical butt spice connectors or tape. My GM/Chevy part # 52413530 (resistor) is replaced by AC delco15-81728. ( ( Full Answer )

How do you replace the blower motor resistor in a Jeep Wrangler TJ?

I'm answering my own question because I found a lot of good information and wanted to simplify it and put it in one spot. If you're Jeep is starting to lose its fan speeds (the slower ones aren't working and the faster or fastest are) then its most likely going to be your blower motor resistor. A ( Full Answer )

How do you replace the blower motor resistor on an s-10 blazer?

You didn't say what year but my 2002 S10 Blazer has the HVAC blower motor resistor located under the hood, on the firewall, passenger side, close to the blower motor. Unplug the wire harness and remove the two small screws holding it in place and gently pull it out.

How do you replace a blower motor resistor 1997 Honda passport?

Resistor is located behind glove box. Remove 2 screw at bottom of glove box which attach hinges. Glove box comes right out. The resistor will be directly behind glove box. It will have a plug and 2 screws which hold it in place. Remove plug unscrew and pull out. Install in reverse order.

How do you replace blower motor resistor infiniti i35?

Remove the 2 glove box latch screws. Click image to see it larger 2. Remove the 4 screws holding the the glove box, two at the top and two at the bottom Click image to see it larger 3. Once the screws are removed pull out the glove box. You may need to use a crew driver to undo the right ( Full Answer )

How do you replace a blower motor resistor for a 1996 Chevy blazer?

I just opened mine up a few months ago (1999 ZR-2) so im doing this from memory... Under the hood, back left you see all the black plastic fairings around the A/C system? On the top, near the firewall there is a molded square (that says "access" if i remember right) around an electrical connector al ( Full Answer )

How do you replace blower motor resistor on 2001 pathfinder?

I WOULD TROUBLE SHOOT FIRST: . 1 . Locate the fuse for the blower motor in the owners/service manual. Test the fuse, with the ignition key on, using the 12-volt test light. Attach the clip lead of the test light to a good ground like a bolt screwed into metal, and touch the sharp probe end to the ( Full Answer )

How do you replace 1997 s10 blower motor resistor?

Locate the resistor under the hood near the blower motor onpassenger side firewall. Unplug the electrical connector. Removethe screws holding the resistor in place. Remove the resistor.Install in reverse order.