answersLogoWhite

0


Best Answer
Copy

Hey Allan===It depends on what engine you have but both are probably the same labor wise. You really need guidance and the best is to get a manual from a parts store and it should have pictures and everything. GoodluckJoe

If you buy an Edelbrock, they come with instructions... Best tip is to insure a good seal, using gasket sealer. The front and rear are known to leak from not enough sealer....and make sure to use a torque wrench, tightening in order and to specs. Recheck and retorque if necessary at next oil change.

Good luck!

User Avatar

Wiki User

โˆ™ 2015-07-15 19:19:48
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you replace the intake manifold gasket on a 1990 4x4 Chevy 1500?
Write your answer...
Submit

Related Questions

How to replace the Intake manifold gasket on a 1996 Chevy Astro?

Remove the intake manifold retaining bolts from your 1996 Chevy Astro Van. Remove the manifold gasket and clean the surface. Reverse the process to install the new intake manifold gasket.


How do you replace the lower intake manifold gasket in a 99 Chevy Venture?

there is no lower intake gasket, only a front and rear gasket


Labor charge to replace a intake manifold gasket on a 99 Chevy Tahoe?

The labor charge to replace and intake manifold gasket, on a 1999 Chevrolet Tahoe, is approximately $180. It takes approximately 2 1/2 hours to replace the gasket.


How do you replace intake manifold gasket on Chevy pick up?

Remove everything on top of the intake (hoses, fuel rails, linkages.) Unbolt the manifold and remove it. Clean the old gasket off and replace it. Reinstall all parts removed to get to the gasket.


Where is the upper manifold gasket located on a 2000 Chevy s10?

Assuming this is a 4.3L engine, the upper intake manifold gasket would be between the upper intake manifold and the lower intake manifold.


How much does it cost to replace an intake manifold gasket on a 1997 Chevy Tahoe 5.7 V8?

The gasket set is $55.00 The labor is $250.00


Where can you find a diagram for installing a intake manifold gasket on 2003 Chevy venture?

is their a web site, that will provide me with the a print out for the intstalling of a intake manifold gasket for a 2003 chevy aenture.


What is the cost to replace intake manifold gasket on 2000 Chevy venture?

well so far it cost me $700.00


1998 Chevy Silverado coolant in engine?

If you are sure that it did not freeze and crack the block, Then the intake manifold gasket is leaking. That is a common problem with the vortec Chevy engines. You need to replace the gasket with a factory Chevy gasket from the dealer.


What is the Labor hours to replace a Chevy 3500 series intake manifold gasket?

It should take about an hour to change the intake manifold gasket. This part can be replaced by taking off the intake manifold cover, cleaning the old gasket off and sealing a new gasket in the space and tightening the bolts. When other things are in the way, like the alternator, it will take longer.


How to change the front intake manifold gasket on a 1999 Chevy Venture?

there is no upper intake gasket, only a front and rear


What is involved with a 350 Chevy intake manifold that is leaking coolant and oil?

You either need a head gasket or intake gasket.


How do you change the intake manifold gasket on a 2005 Chevy Trailblazer?

www.trailvoy.com


How do you replace a head gasket on a 1999 Chevy Malibu?

The head gasket on a 1999 Chevy Malibu is replaced by removing the coolant, intake manifold, and retaining bolts. The cylinder head can then be removed, the gasket replaced, and everything reassembled.


What will cause antifreeze to mix with oil in a 2000 Chevy Monte Carlo 3.4?

You need to replace your intake manifold gasket. Chevy had a bad problem with these gaskets.


How do you install a head gasket in a 2005 Chevy Cobalt?

Remove intake and exhaust manifold. Remove head and replace the gasket. This is a major repair best left to a professional.


Where is the upper intake gasket on a 2001 Chevy blazer?

It is between the upper and lower intake manifold. The gasket is an o-ring type.


How do you change the intake manifold gasket in a 3100 Chevy lumina?

take it to a mechanic


How long does it take to replace a intake manifold gasket at a shop on a 92 Chevy k1500 truck with a 350 tbi motor?

About 2 hours.


On your 350 Chevy how to stop coolant leak between heads and maifold the heads have rear water jackets the manifold does not?

replace the intake gasket set


Where is the knock sensor on a 2002 Chevy Avalanche?

They (2ea.)are in the intake. The intake manifold will need to be removed to get to them. The wire harness and intake manifold gasket should both be replaced when reassembling.


How do you replace intake manifold gasket on a 2000 Chevy blazer?

i have the haynes book from auto zone for mine, it has step by step instructions for taking off your intake manifold. i know cause im pretty sure my gasket just blew saturday.....so i been researching it also


Have a 1988 Chevy impala with a 305 burning coolant what could be the cause?

a bad head gasket or intake manifold gasket.


Torque specs for 2003 Chevy Silverado 5.3L intake manifold?

how tight do torgue specs need to be after insalling a intake gasket on a 2003 Chevy silverado


Where is the Knock sensor on a 2001 1500 5.3 V8 Silverado Located and is there a specific way to change it?

There are two knock sensors on a 2001 Chevy 1500 with the 5.3 V8. You have to remove the intake manifold, because both of them are located under it. it is best to replace both knock sensors at one time, and you will need an intake manifold gasket too. There are two knock sensors on a 2001 Chevy 1500 with the 5.3 V8. You have to remove the intake manifold, because both of them are located under it. it is best to replace both knock sensors at one time, and you will need an intake manifold gasket too.