Water Pumps
Acura Integra
Dodge Durango

How do you replace the water pump on a 1993 Acura Integra?

232425

Top Answer
User Avatar
Wiki User
Answered
2005-10-28 04:57:46
2005-10-28 04:57:46

Changing a water pump can be a very time consuming and complicated process. First and foremost, get a service manual (highly recommend a Helms; if you must, a Chilton will do), follow the instructions. Do not attempt to do this without written instructions from the engineers who actually built the 1993 model Integra. Here's what I learned over the years regarding this DIY project: - Mechanics recommend replacing the timing belt along with the water pump while you

012
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


A 1993 acura integra gsr transmission.. Wat kinda question is that?

no the 1993 acura integra headlights will not fit the 1995 integra, 90-93 acura integra are more of a rectangle shape as to where in the 1994-2001 integras except the type r, have round head lights

The gap for a 1993 Acura Integra is 0.44. Use a gapping tool.

To change a starter from a 1993 Acura Integra remove the mounting bolts that connect it to the transmission. Then unplug the solenoid from the wire harness. Install the new unit.

Directly below the intake camshaft. Its near the drivers side engine mount. Its a good idea to replace the timing belt and tensionor at the same time as the water pump.

Fot the 1993 acura integra timing belt 'cord' specifications. Is the honda made timing belt from fiberglass or kevlar ?

It will not work. A 1993 Honda Accord has a 4x114.3mm bolt pattern. A 1997 Acura Integra has a 4x100mm bolt pattern.

it can be lost of Compression in the Motor....

1-3-4-2 in a clockwise rotation... = 1993 Acura Integra 1.8 liter DOHC L4 =

Yes it should. Im 99% sure it will. you might want to double check the part number to see for sure. i have a 1990 Acura integra and i have used many parts from integras from 1990- 1993.

The thermostat is located at the other end of upper radiator hose.

Remove fitting at junction block (usually at center of rear axle) and disconnect at the wheel cylinder Replace line and bleed air from that wheel. Should only have to bleed that line

its easy located on the pass side of car under hood sze of a pop can 2 lines just follow the line from the fuel rail to the filter

check for a blown fuse that says heater or blower motor

3.9 quarts but its best to just put all 4 quarts in.

Check the fan. Sometimes the wires come unplugged. Mine does it sometimes too.

You can get the fuse layout by looking at your owners manual that comes with the car. It should have the layout of the fuse and it will show which fuse is what.

Check your relay which is under the instrumental panel on the left. When you are seating down on the driver seat, it will be above your left leg. Look for cold solder and re-solder it.

On the break pedal assembly, it's kind of hard to get there but it's a little black button. When it's pushed in, the lights turn off and when it's depressed, the lights turn on.

the b18b1 is a dual overhead cam 1.8l engine produced by Honda motor company. It was put in some 1990-1993 acura integras and was put in 1994-01 Acura Integra LS.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.