Chevy Corvette
Ford Expedition Eddie Bauer
Ford Expedition XLT
Ford Explorer Limited

How do you reset the change oil light on a 1993 Corvette?

232425

Top Answer
User Avatar
Wiki User
Answered
2006-12-31 23:25:45
2006-12-31 23:25:45

To reset the oil light, put the key in the ignition and turn to accessory setting (but do not start the car) Push the English/Metric button twice and then push and hold the "Range" button. The "Change Oil" light will flash for about 15-20 seconds and then go out. Release the button and turn key off. When you turn the key back on, the light should be out. If it is not, repeat the above steps.

123
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


= How do you reset change oil soon light on 1993 buick park avenue? =

How do I change the dimmer switch on my 1993 corvette?

Turn the key to the Run position, but do not start the engine. Press and release the ENG MET on the trip monitor. Within five seconds, press and release it again. Within five seconds press and HOLD the GAUGES button on the trip monitor. The CHANGE OIL light will start to flash. Hold GAUGES botton until flashing stops. Light is now reset.

will a 1985 corvette hood fit a 1993 corvette

It depends. If the sensor is working, just reset the computer. Otherwise you have to change the sensor.

There isn't a switch to reset the light. You 'reset' the light by fixing the problem which is causing the light.

You need to repair the cause of the code that turned the light on. You can then reset the light with a scan tool or a battery disconnect.

Go to Autozone or Advance They will reset it for free.

1993-1996 Fleetwood1. Turn the ignition key to the RUN position.2. Fully depress and release the accelerator pedal 3 times within 5 seconds.3. The CHANGE OIL light should flash two times and then go out.4. Turn the ignition OFF.If the CHANGE OIL light comes on and stays on for 5 seconds, it did not reset. You'll need to reset the system again. 1991-1993 Deville, & FWD FleetwoodWhen "CHANGE OIL SOON" light is illuminatedPress and hold the "RESET" and "RANGE" buttons on the Fuel Data Center for 5 to 60 seconds. When the buttons are released, the light will flash four times if it has been reset. If the light comes back on for more than 5 seconds, repeat the procedure. [http://myweb.accessus.net/~090/cadireset.html Available At] Good Luck and Remember.Change Your Mind, Not Your Oil.Use the First In Synthetic Motor Oil's.See My Bio For more information.

there should be a small hole beside the panel the light sits in. straighten a paper clip and push the button inside the small hole.

Almost 5,700 1993 Corvette Convertibles were produce and sold that year. James

Odds are you have an optispark unitl. If so it is under the water pump on the front of the engine. Look up optispark replacement on LT1 or C4 Corvette.

take off the belt, use a pulley puller to pull it then reinstall.

Yes, they are a direct fit. TOM

A 1993 Jeep does not have a reset switch.

A Check Engine light can be reset by fixing the problem that caused it to go off. The codes that caused the light to go off can be cleared with an OBD II scanner.

you will go to the toyota dearler it good pleace

You will first need to check that the airbag has been properly set up. Then you can go into your settings and get it all reset.

Remove the water supply hoses from your 1993 Chevy Corvette heater core. Some water will drain out of the hoses and the heater core. Remove the heater core retaining bolts. Reverse the process to install the new heater core.

Corvette didnt have a Crankshaft Position Sensor until 96.

Are you asking about the courtesy lamps inside a Corvette? It helps to know the year since they change from year to year. It's Corvette 1993 But does not work because of security system lamp on


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.