0
How does the power steering pump bolt on a 1978 cj5 with a 258 motor?
Wiki User
∙ 16y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Bolt size for Honda civic rear motor mount bolt?
What size bolt for a 2005 Honda civic DX power steering tank bracket..
How do you replace the water pump on a 1995 delta Royale and Does the belt pulley at the bottom of engine close to firewall and motor mount have to be removed?
The pulley you are referring to is the power steering pump pulley and yes you need to unattached the power steering pump from the engine. This is done by removing two bolts behind the pulley. There are three large holes in the power steering pulley and these holes will allow you to gain access to the two power steering bolts. One bolt is located at the top right of the power steering pump and the second bolt is located at the bottom left. Once these bolts are removed the power steering pump will drop down and pivot towards the firewall. DO NOT DISCONNECT THE POWER STEERING HOSES. This is not necessary since the power steering pump is not being replaced. This will give you the clearance you need to access the bolts without obstructions. For the removal of the Serpent belt you will need to remove ONE engine mount bolt. The motor mount bracket is attached to the engine in three points. The engine mount itself sits on top of the frame. Standing over the passenger side fender and looking into the engine compartment you will see the attachment points for the motor mount. The bolt on the bottom right side of the motor mount must be removed. You will need an E8 torx socket for this (it is a stud bolt with a nut, since this is an older car, the nut may be rusted to stud, so the stud may come out by placing a socket on the nut...so an E8 socket may not be required). Once the bolt is pulled away from the motor remove the spacer between the motor mount and the engine which will allow the Serpent belt to be removed. DO NOT REMOVE OR LOOSEN ANY OTHER MOTOR MOUNT BOLTS. This is not necessary. If you remove or loosen any other motor mount bolts you will need to support the engine. Good luck. Rob
Hw do you remove power sterring pump pulley on a 91 Cadillac Seville?
Begin by removing the power steering pump belt from your 1991 Cadillac power steering pump pulley. Remove the power steering pump pulley retaining bolt. The retaining bolt will be in the center of the pulley.
Which bolt is the one to loosen when changing the power steering belt?
How does one change a power steering belt on a 1997 nissan pickup?
How do you reach the bolt on the water pump of a 1995 buick park avenue that is covered by a power steering pulley?
remove the power steering pump
How do you change the power steering hose on a 2002 Nissan maxima?
Disconnect the negative battery cable.Drain power steering fluid.Loosen adjustment screw and power steering pump through bolt, then remove belt.Remove power steering pump union bolts and hose.
Where are the set bolt pivot bolt and tensioning bolt on an 1985 jetta power steering pump located?
www.kiss my bolty pivot ass.com
Will a 1992 Chevy 427 motor bolt to a 1978 Chevy 350 turbo trans?
No. blocks are not the same.
I cant find it I've looked on the firewall but no dice. should it be on the intake somewhere?
if your looking for the Crankshaft Position Sensor(3.4 motor v6) its behind and below the power steering pump on the intake, in the middle front top of the motor (1) bolt holding it down.
Remove power steering hose on 2007 GMC c5500?
unscrew the bolt and it will come off
About to change out the upper and lower manifold gaskets How did you break the bolt loose holding the power steering pulley?
On my 99 Suburban, You have to rent or buy a puller for the power steering pump pulley.
99 where is the camshaft position sensor bank one?
It is behind the power steering pump on the passengers side of the engine. It requires removing the power steering pump and there is a little bolt and it pops out.
