BMW 3-Series
Oldsmobile Intrigue
Crankshaft Sensors

On a 2000 Olds Intrigue where is the crankshaft position sensor located?

434445

Top Answer
User Avatar
Wiki User
2009-12-31 05:43:01
2009-12-31 05:43:01
I have Olds Intrigue 2000 3.5L. Needed to replace faulty crankshaft sensor.3.5L engine has two of them.

If engine is hard to start cold or hot and engine light is OK.

Very common problem for this engine in Aurora 3.5 and Intrigue 3.5 is crankshaft position sensor. Which is located above and behind starter. Starter must be removed first.

------------------------------------------------------------------------------------------------------------

Answer

Lower right hand side of the engine just above the oil pan. Theres a single bolt that holds it in.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The crankshaft sensor is in the front of the engine.Above the starter.You will have to drop the starter.2 15mm bolts.Look up and there it will be.

User Avatar

depending on the year, I have a 2002 intrigue, it is located just above the starter, it needs to be removed to remove the crankshaft sensor, 15mm for starter and 10mm for sensor 1 bolt , not to difficult.

User Avatar

where is the camshaft position sensor located on a 1999 Oldsmobile intrigue

User Avatar

where is crankshaft position sensor and camshaft position sensor on a 2004 Jetta 2.0 gl

User Avatar

how to replace the crankshaft position sensor located in a 2003 kia rio

User Avatar

Where is the crankshaft position sensor located on Audi 2002 Audi TT

User Avatar

The crankshaft position sensor is located on the front of the engine. It is just to the left of the crankshaft pulley.

User Avatar

The sensor in the distributor is the crankshaft position sensor.

User Avatar

The crankshaft position sensor is located behind the timing cover and above the crankshaft gear. the timing belt my have to be removed to access the bolts on the sensor.

User Avatar

Someone believes you should, "Take Your coolant tank off and the sensor is located under it. It's fairlly simple to replace once you find it."; You will find a sensor there but not the crankshaft sensor. On a 99 Intrigue with a 3.5L, the crankshaft position sensor is in the engine block just above and behind the starter. get under the car, remove the starter and you should find what you are looking for.

User Avatar

The crankshaft position sensor, on your 1992 Buick regal 3.1 liter, is located on the back of the engine. The crankshaft position sensor is on the inside of the engine cover.

User Avatar

The 1995 Mitsubishi Eclipse crankshaft position sensor is located on the back of the engine. The crankshaft position sensor will be near the bottom of the engine cover.

User Avatar

On my 1995 Mercedes Benz E320 where is located the crankshaft position sensor?

User Avatar

The crankshaft position sensor on a Buick is located behind th Harmic balancer. It should have a wire plugged in to it.

User Avatar

The sensor is located directly above the crankshaft pulley. The camshaft sensor also connects with the crankshaft position sensor.

User Avatar

The crankshaft position sensor is located at the lower left hand side of the crankshaft pulley. The crankshaft pulley is the large pulley located in the center lower portion of the front of the engine.

User Avatar

Answerthe camshaft sensor is the distributor but the crankshaft position sensor is located right next to the crankshaft its held on by one bolt

User Avatar

The crankshaft position sensor on a 2005 dodge grand caravan is located on the top side of the bell housing.

User Avatar

The crankshaft position sensor is located on the front side of the engine block near the flywheel/driveplate

User Avatar

it is located on the side of the transmission

User Avatar

The crankshaft position sensor for the 1995 Monte Carlo is located on the front of the engine. It is just to the right of where the crankshaft comes out of the engine.

User Avatar

The crankshaft position sensor is located on the front side of the engine block near the flywheel/driveplate

User Avatar

The crankshaft position sensor is mounted in the transmission bellhousing at the left/rear side of the engine block


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.