0
Rover 75 Clutch just stopped working slave cylinder dry but no sign of leakage do you need to refill and bleed or buy new one?
Wiki User
∙ 14y ago
If no signs of leakage at slave operating cylinder,then check clutch master cylinder for leakage,and look at clutch pedal and see if you see any clutch fliud as rod comes thru firewall.follow all lines.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What does it mean when the clutch sticks all the way to the floor on a 1997 Chevy cavalier z 24?
The clutch release ("throw-out") bearing has gone bad...Use a new clutch disc when you replace the clutch release bearing...or it could be the clutch master cylinder. Check the master cylinder first...Look for any sign of leakage from either component .
Why is your clutch not working for a 1985 Toyota pickup?
So many answers to such a vague question. Clutch is worn out, clutch cylinder not working, release bearing seized, out of adjustment. How about some details?
Where is The location of slave cylinder in 1984 jeep cj7?
my clutch is not working ..think the slave cylinder is bad ..135 , 000 miles ..
What would cause loss of clutch fluid with no signs of leakage on a 1999 Chevy cavalier?
It is either leaking down the inside of your firewall under the dash (master cylinder) or leaking just enough inside the trasnmission bell housing to not puddle and be thrown around by the clutch spinning (slave cylinder).
Ac clutch not working on a 2000 VW jetta VR6?
If it has stopped working then you will need a new a/c compressor. Get out your wallet they will run you about $1200.
What if your clutch on your 85 Toyota corolla goes to the floor and is hard to shift?
There are two normal causes. The clutch is worn out or there is a leak in the hydraulic clutch slave or master cylinder. To check the clutch, press the clutch slave cylinder down. If the clutch slave cylinder bellows compresses down to the slave cylinder, the clutch is worn out. Check the clutch master cylinder fluid level. if this is low, then the clutch cylinder need to be checked. To check for a hydraulic leak in the clutch slave cylinder, remove the cylinder's bellows and check for any fluid. If fluid is present, rebuild or replace the cylinder and bleed the system. To check the clutch master cylinder, check the back the of clutch master cylinder for leaks. If fluid is present, replace or rebuild clutch master cylinder and bleed the system. In my experience, hydraulic leaks occur at the clutch slave cylinder.
The clutch was replaced on a 1994 Mazda B3000 with a complete kit then it stopped working two weeks later the slave cylinder looked good and then seems to work again what else could be wrong?
94 the year of Ford auto clutch. It has allways been a problem. Plastic parts fluid leaks.
Why is the clutch on a 1994 Chevy Cavalier not working?
Most of the time it is because of a bad slave cylinder that does not hold pressre or is leaking. They use brake fluid and to check them look at the CLUTCH MASTER CYLINDER near the firewall.
Should you replace your clutch master cylinder when replacing clutch?
At least the slave cylinder. The clutch master cylinder can be replaced at any time.
What connects slave cylinder to clutch pedal on 1987 ford ranger?
The clutch pedal assembly has a clutch rod that pushes in on a clutch master cylinder. There is a hydro line that goes from the master cylinder to the slave cylinder.
What does the master and slave cylinder do for the clutch?
The master clutch cylinder is attached to the clutch pedal. When one depresses the pedal hydraulic fluid is forced from the master cylinder through the hard line to the slave cylinder. The piston in the slave cylinder is driven against the clutch linkage thereby releasing the clutch.
Why would a 1993 Nissan 300ZX not go into gear?
The most probable cause is that the clutch is either not releasing; master/slave cylinder not working, or the clutch itself is damaged.
