0
Viper alarm LED stays on when I turn the car off and remote unlock and lock works but does not make the alarm chirp when I lock it or unlock it?
Wiki User
∙ 13y ago
Your alarm system is in valet mode. To fix this problem:
Unlock the car, and open the door.
With the door open, and the car unlocked, press:
LOCK/UNLOCK button ONCE, press the AUX button ONCE, and then press the LOCK/UNLOCK button ONCE more.
When you press this key combination, the vehicle security system should begin functioning correctly again.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you program a 98 vw jetta key fob?
Matching instructions for the Clarion 1993 to 1999 banjo style remote. Using 2 keys, put one key in the ignition, turn the igniton on, do not start the car. Close the door, put the 2nd key in the door lock, turn the key to the unlock position and hold it untill you hear the alarm horn chirp, release the key. Press any button on the remote, you should hear a chirp from the alarm horn, press button on the 2nd remote, you will hear two chirps, 3rd remote will chirp 3 times, and the 4th remote will chirp 4 times, then lock the door with the key. Unlock the door, remove the key from the ignition, close the door and try the remote. You can match any remote to any car. You teach the car to respond to each remote. www.watercooledkey.com
Is it best to get VW Jetta replacement keyless remote at the vw dealer?
I just bought a replacement remote at www.keylessride.com . It was $45 plus tax and came with free programming instructions. The dealership was going to charge me $80 to program. My 16 yr old son and I programmed it in less than a minute. Matching instructions for the Clarion remote 93-99. Using 2 keys, put one key in the ignition, turn the igniton on, do not start the car. Close the door, put the 2nd key in the door lock, turn the key to the unlock position and hold it until you hear the alarm horn chirp, release the key. Press any button on the remote, you should hear a chirp from the alarm horn, press button on the 2nd remote, you will hear two chirps, 3rd remote will chirp 3 times, and the 4th remote will chirp 4 times, then lock the door with the key. Unlock the door, remove the key from the ignition, close the door and try the remote. You can match any remote to any car. You teach the car to respond to each remote. www.watercooledkey.com
How do you take the alarm off of silent on a 1998 Chevy Malibu?
with the ignition on, hold the unlock switch for 10 sec. you should hear chirp
On a 2002 Hyundai How do you make the alarm chirp instead of being silent I have a factory alarm and I have no idea how it works Someone help me?
Generally, you press the remote button once and the alarm arms and the lights flash once. If you press it a second time, the lights flash again and the alarm chirps.
Why doesn't my Nissan Xterra beep when I lock my car with my remote?
The beep function on the remote may be deactivated. To reactivate, simultaneously hold both the lock and unlock button for about three seconds. The car should chirp and the lights flash.
How do you reset the chirp on a 2000 Toyota Sienna when you lock it with the remote?
i dont think you have chirp only lights will flush
How do you program a key less entry?
to 2003 subaru outback onlyWell i have been researching this as I have a Subaru Liberty 2004(AUST)(legacy elsewhere)as I want to change the setting so that it opens the drivers door only and requires a second push to open all. Saves wear and tear)Subaru can do it for me but I am sure it is simple. i have this articale below which was written on another site for an older model Subaru. Plus i can also get the amount of time the light stays on when pressing unlock as well. I am certain it is a combination of key presses. But which ones? . Locking. Larger, orange button. Push the lock button. This locks all the doors and will set the alarm (if equipped and in 'setable' mode)2. Unlocking. Smaller, blue button Driver's door only: Push the unlock button once to unlock the driver's door and also disarm alarm if set. All doors: Push the small button *firmly* a second time within a few seconds to unlock all the doors.3. Chirp horn? The chirp is once for lock, two times for unlock, multiple times if a door is ajar when you try to lock them. This is optional. To turn the audible on or off unlock all the doors and hold *both* buttons down until the horn honks. The horn will always chirp repeatedly if a door is not fully closed when you lock with the remote.5. Alarm. Valet mode or alarm off: alarm light (red dot center dashboard dispay) rapidly flashing 3 times/pause means the alarm is in "Valet" mode and is not setable. This light will stop flashing when you start the car.Arming the alarm: to re-enable an alarm in valet mode, Unlock all the doors and hold the small button down on the remote until the light stops flashing. Now when you lock the doors the alarm will be set and the light will slowly flash on and off, on and off.6. Alarm goes off? Push the small button on the remote or if you don't have the remote put the key in the ignition and turn it on and off three times.7. Program remotes: works on all with Alpine system. unlock all doors. Cycle key quickly but carefully on-off app 10 times until the car honks one time. Do not turn the key far enough to start the car. Just to the 'on' position so the dash light up. When the car honks, open and close the driver's door, press a remote button and that's it. Program another remote? Open and close the door again and push the 2nd remote button. When you're done, remove the key and the horn should honk 3 times. You're all set. Sometime it takes me more than 10 on-offs to make the horn honk, sometimes you need to start-turn off the car, lock-unlock the doors a few times, wait a while etc. But is does work.
How do you program a key-less entry?
to 2003 subaru outback onlyWell i have been researching this as I have a Subaru Liberty 2004(AUST)(legacy elsewhere)as I want to change the setting so that it opens the drivers door only and requires a second push to open all. Saves wear and tear)Subaru can do it for me but I am sure it is simple. i have this articale below which was written on another site for an older model Subaru. Plus i can also get the amount of time the light stays on when pressing unlock as well. I am certain it is a combination of key presses. But which ones? . Locking. Larger, orange button. Push the lock button. This locks all the doors and will set the alarm (if equipped and in 'setable' mode)2. Unlocking. Smaller, blue button Driver's door only: Push the unlock button once to unlock the driver's door and also disarm alarm if set. All doors: Push the small button *firmly* a second time within a few seconds to unlock all the doors.3. Chirp horn? The chirp is once for lock, two times for unlock, multiple times if a door is ajar when you try to lock them. This is optional. To turn the audible on or off unlock all the doors and hold *both* buttons down until the horn honks. The horn will always chirp repeatedly if a door is not fully closed when you lock with the remote.5. Alarm. Valet mode or alarm off: alarm light (red dot center dashboard dispay) rapidly flashing 3 times/pause means the alarm is in "Valet" mode and is not setable. This light will stop flashing when you start the car.Arming the alarm: to re-enable an alarm in valet mode, Unlock all the doors and hold the small button down on the remote until the light stops flashing. Now when you lock the doors the alarm will be set and the light will slowly flash on and off, on and off.6. Alarm goes off? Push the small button on the remote or if you don't have the remote put the key in the ignition and turn it on and off three times.7. Program remotes: works on all with Alpine system. unlock all doors. Cycle key quickly but carefully on-off app 10 times until the car honks one time. Do not turn the key far enough to start the car. Just to the 'on' position so the dash light up. When the car honks, open and close the driver's door, press a remote button and that's it. Program another remote? Open and close the door again and push the 2nd remote button. When you're done, remove the key and the horn should honk 3 times. You're all set. Sometime it takes me more than 10 on-offs to make the horn honk, sometimes you need to start-turn off the car, lock-unlock the doors a few times, wait a while etc. But is does work.
How do you program a 1998 Jeep Grand Cherokee alarm to chirp?
I believe you have to take it to a Jeep dealership & they can program it. If you keep pressing the unlock button on your key fob (about four times) it will start chirping. The same for locking.
How do you program a gm21997127 remote for a 2006 Chevy Equinox?
Enter your Equinox with your keyless remote and your ignition key and turn the key in the ignition to the "On" position.2 Press the vehicle information button until the display reads, "Press to Relearn Remote Key."3Press the set button until the display reads "Remote Key Learning Active."4 Press and hold the unlock and lock buttons on the remote that you are programming until the car responds with a chirp.5 Repeat step 4 with any additional alarm remotes and remove the key from the ignition to end the programming sequence.
How do i program keyless remote for 06 Chevy impala?
you have to resync the remote after changing the battery, stand next to car hold the lock and unlock buttons down for about 7 seconds or until you hear the horn chirp, thats it good luckSource(s):Impala LS owner
Your expedition alarm now chirps and goes off if you try to use the keyless entry keys It used to not chirp and the keyless entry keys worked fine Suggestions?
I'd try reprogramming the the remote. You should have instructions with in your users manual. If that doesn't work you might need a new keyless remote.
