answersLogoWhite

0


Best Answer

Tha is not as much a repair as it is a rebuild job. The crankshaft is in the bottom of the engine and it's best to remove the engine for that kind of repair. Next then is buy a rebuilt or good used engine to put back in if you're going to keep it. Otherwise - go to the library and check out a motor manual and learn something about rebuilding engines.

User Avatar

Wiki User

โˆ™ 2006-02-23 20:54:22
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: What and where is a crank shaft and how hard will it be to repair on a 1984 Delta 88 307 engine?
Write your answer...
Submit
Related questions

Where is your crank shaft located on a 2000 ford expedition?

The engine crank shaft is inside the engine


What happens if your crank shaft belt breaks wile driving?

If the crank shaft breaks you will have catastrophic failure of the engine with major damage. Bascially the engine will self destruct and you will have to install a new short block to repair it.


Where is the Crank Sensor in a 2001 Malibu?

The crank sensor on a 2001 Malibu is located on the bottom of the engine near the crank shaft. It monitors the rotation and speed of the crank shaft.


How can you repair threads on end of crank shaft?

you cant. replacement required


Where is the crank shaft sensor in a 1997 sebring convertable?

crank shaft sensor is near the oil filter. I have the repair manual but I am unable to past the page in here.


Where is the location of crank sensor for range rover v8 4.6HSE MODEL 1999?

The 1999 Range Rover 4.6 liter engine crank shaft sensor is located on the back of the engine. The crank shaft sensor is behind the rear engine cover.


Where is the crank shaft sensor on a 2000 suburban?

The crank shaft sensor on a 2000 Chevy Suburban is located on the bottom of the engine, near the oil filter. It constantly monitors the crank shaft and updates the vehicle's computer of its status.


Where is the crank sensor located on 1998 Bravada?

the crank sensor is located just behind the crank shaft pully of the engine.


Where is the crank shaft position sensor on a 1999 Oldsmobile intrigue 3500 engine?

The crank shaft positioning sensor is behind the starter. A real bear to get to.


Will the engine turn over by the crank shaft bolt if it is seized?

No


Where is the crank shaft sensor on a 2003 fiesta?

Engine type ??????????


What if your car runs fine but the computer says you have no crank shaft signal?

The crank shaft sensor may have died and the engine controller is using other sensors to keep the engine operational in "limp" mode.


Speed ratio between cam shaft and crank shaft?

Cam spins at half the speed of the engine.


Do you need a Crank Shaft Head to put on a Crank Shaft in Lacrosse?

I would recommend that you do put a crank shaft head on a crank shaft. Putting any other type of head on a crank shaft could possibly break the head.


What is OBD code P0320?

Crank shaft/ engine speed sensor malfuntion.


Where is the crank shaft sensor on a 1998 cavalier?

Its on the backside of the engine, on the firewall side


Where is crank shaft sensor on 1996 chev?

Need to know what size engine it has.


Which part is conet in engine and crank shaft?

i thik a chine is conect in between them.


Where is the crank shaft sensor loacted on the engine for 1996 F-250 7.3 diesel?

The crank shaft sensor is located on front of block above the harmonic balance wheel (bottom pulley on front of engine). This is easiest to get at from underneath the vehicle.


Where is the crank shaft sensor on a 1994 buick lesabre?

under the crank pulley, right side of car under front of engine


Where is the crank shaft located on a 2000 Chevy blazer?

Inside the bottom of the engine block.


The Car makes clunking sound from underneath when engine is started?

could be your crank shaft


What cause the engine to have a knocking noise on 3.0 liter Toyota Avalon?

Crank Shaft.


What is a crank in a car?

Crank shaft


What is involved in fixing a spun rod bearing?

The easiest repair is to replace the engine. Otherwise the crank shaft will need replaced/remachined and the connecting rod will need replaced. Basically a complete overhaul.