answersLogoWhite

0


Best Answer
Copy

Make sure you know what plug wire goes where on your distributor or coil pack to plug.

Pull plug wires. Use spark plug scocket to remove all 4 plugs. Don't know what plugs it calls for but use the right plugs. Plugs must be gapped. The gap should be on sticker under hood. re: .44 or.52.

Replace plugs by hand. Do not cross thread. Tighten. If you don't have the torque spec, the hardest you can tighten the plugs with the wrench only using 2 fingers should be good. DO NOT OVERTIGHTEN. You can break one.

Replace wires.

If you have a distributor, you may want to check for cap and rotor.

AnswerI would only add that you do one plug and plug wire at a time, instead of pulling all wires at once. This way you will not lose track of what wire goes where. AnswerThe 93 Ford Ranger 4cyl has 8 spark plugs, 2 per cylinder. The are spark plugs that are under/blocked by intake manifold components, which have to be removed to gain access to the plugs. Removal can also be attemped using several special tools, a mixture of swivel sockets, long extensions, etc(it easier to remove the intake manifold components). Make sure that you replace all 8 spark plugs and wires(8)at the same time. Use the correct plugs. Ford recommend that you do this every 30,000 miles. New Answer - Posted by Steven In NCThis is a little time consuming. Print this out. Decide if you have patience enough to do the job, or pay Precision Tune $398 to do the job.

As stated above the Ranger 2.3L has 8 plugs, 2 per cylinder. First, buy good platinum plugs so you won't have to revisit this in another 30K miles...but rather 60-80K. Also, buy top quality spark plug wires and do them at the same time. Here is how to proceed.

Tools you will need. (2) 6inch extensions for your 3/8ths inch socket wrench.

(1) 3inch extension for your 3/8ths inch socket wrench.

(1) Swivle Socket extension for your 3/8ths inch socket wrench.

(1) Small flat head screw driver.

(1) Large flat head screw driver for the intake tube clamp on the throttle body.

(1) 1/2inch socket for exhaust manifold studs.

(1) Spark plug socket with rubber insert to hold plugs in place while inserting & removing.

Some liquid wrench or WD-40.

Some Anti-seize for your spark plugs.

Some Dielectric grease.

Magnetic Pickup Tool may be needed.

Needlenose Pliers

Preparation Steps: Prep Step A - Unhook the round air intake where the air filter is located on the passanger side of the vehicle.

Prep Step B - Loosen the clamp that holds the air tube to the throttle body intake and pull the tube off.

Prep Step C - Remove the tube from the top of the engine that circulates the crankcase air back through the intake tube. It's located right behind the oil filler cap.

Prep Step D - Move the entire air intake tube towards the front of the vehicle and lay it on the radiator/fan area.

Your now ready to start.

Start with the passanger side of the engine. It is relatively clutter free. Start with the 1st cylinder at the front of the engine.

1. Twist & remove the spark plug boot from the existing plug.

2. Use a very small flat edged screwdriver to pry open the clips that hold the plug wires together. Note the entire clip is easy to slide off of the little round mounting grommet attached to the engine...then you can hold it in some good light to get a better view of how to open it with the little flat edged screw driver.

3. Use a 6" extension & a 3" extension & your deep socket for the spark plug. I believe it is a 5/8ths...but can't remember for sure.

4. Remove the first plug, yes it will be tight against the 2nd coil pack, but it does remove without taking the coil pack off.

5. Replace the old plug with a new Bosch Platinum Plus 2 prong plug and use some anti-seize on the threads and tighten to the appropriate torque. For me, that's tight but not too tight.

6. Remove the old plug wire from the coil pack. It will be going to the 2nd coil pack (located to the rear of the first coil pack).

7. Install your new plug wire on the coil pack & coat the inside with some dielectric grease if you have some or if the plug wire set comes with some.

8. Repeat steps 1-7 for plugs on 2 & 3.

9. Plug #4 - the last plug on the passanger side. Remove the two (2) 1/2inch bolts that holds a bracket to the exhaust manifold. Make sure you spray the studs these bolts are on with some DW-40 or liquid wrench. Exhaust manifold studs are notorious for having a lot of rust & being difficult to turn nuts off without shearing off the stud & banging up your knuckles at the same time. It has some sort of aluminum box ontop of this bracket with some sensor wires coming out of it. Slip the bracket off and simply lay it to the rear of the engine to provide better access to this last cylinder.

10. Repeat steps 1-7 for plug #4.

11. Remount bracket containing the aluminum box with sensor wires. Tighten the two 1/2 inch nuts back down.

You have now completed the passanger side of the vehicle. It's should only have taken you about 45 minutes if you were working slow.

Now it's time to do the hard side. The drivers side of the engine appears to be literally encased in fuel injection wiring, and the intake manifold. Slow down, take a break, breath deep. You will NOT have to remove the intake manifold to accomplish this.

Step 12 - You will notice on the first cylinder at the front of the engine the spark plug wire has a grey handle sticking up next to the A/C compressor. Using some pliers (needle nose worked for me) twist & pull this grey handle. The spark plug boot should pop free.

Step 13 - Using your small flat edged screw driver, unhook the spark plug wire clips that hold the wires together. There are 3 - One just after the 1st coil pack located at the front of the engine, another just on the other side of the valve cover and a small 2 clip located about 1/2 way back on the valve cover under the intake manifold. Remember you can slip these clips off of their round mounting points to make access easier to un-hook the clips.

Step 14 - Remove the spark plug wire from Cylinder #1 on the Drivers side.

Step 15 - Using the small flat edged screw driver press the 4 connection points on the grey handle that is attached to the wire. It will separate down the middle and allow you to remove the wire.

Step 16 - Replace the wire with the new wire - ensure you line up the rubber round plugs with the round holes in this grey handle & snap it back together with the new wire in place.

Step 17 - Hold the spark plug socket in your left hand down near the plug. Now feed a 6" inch extension below the A/C Compressor line (black pipe) and the A/C Compressor with your right hand and attach the spark plug socket into the extension. (It will not fit if you try to slide the socket between the Compressor and the black A/C compressor line.)

Step 18 - Slip the socket onto the plug. Attach an additional 3 or 6 inch extension to the existing extension & attach your socket wrench.

Step 19 - Remove the plug & proceed to replace it with a Bosch Platinum plug & anti-seize on the threads.

Step 20 - Feed your new Spark Plug wire over to the 1st coil pack & replace it on the coil pack.

Step 21 - Take a break. Get some water.

Step 22 - Move on to the second spark plug. There is no grey handle on the second spark plug boot. You will be able to reach it & twist the boot and remove it. Replace the wire as you have done previously on the first coil pack.

Step 23 - To remove the second spark plug use your spark plug socket and a 3inch extension. Slide the extension & socket onto the plug. Next get a swivel socket adapter for your 3/8ths inch and attach it to a 6 inch extension. Now connect the 6inch extension & the swivel socket adapter to the 3inch extension. You will now find that it does not bind very much and you will be able to loosen the #2 spark plug.

Step 24 - Repeat Step 19.

Step 25 - Attach the spark plug wire to the plug.

Step 26 - Another break & more water.

Step 27 - Look between the intake manifold tubes & you will see another grey handle for spark plug number 3. Using needle nose pliers reach in between the intake manifold tubes and twist & pull the spark plug boot off.

Step 28 - Un-hook the spark plug wire from the 1st coil pack. Now is a good time to check and make sure you got that 3rd wire clip un-hooked so the spark plug wire will move easily. Now pull the plug wire out between / through the intake manifold tubes until it is free from the engine. Careful, go slow feed with your left hand while pulling slowly with your right hand.

Step 29 - Repeat steps 15 & 16 with this plug wire.

Step 30 - Using a 6 inch extension & another 6 inch extension hooked together, put your spark plug socket on and slide it between the intake manifold tubes and onto the spark plug. Remove the spark plug. If it drops out of your socket, use a magnetic pickup tool (telescoping rod with a magnet on the end) and retrieve your plug from the top of the intake manifold.

Step 31 - Repeat Step 19.

Step 32 - Feed your new spark plug wire through the intake manifold tubes like you removed it. With the coil pack end first and reach behind the intake manifold (yes it's tight but you will be able to feel it) and slowly pull it towards the front of the engine while feeding the plug wire with your other hand.

Step 33 - Using the grey handle and a flashlight, line up and push the plug wire onto the spark plug using your pliers again.

Step 34 - Repeat step 26.

Step 35 - Move to the last plug...your almost there..hang in there! Look between the last 2 intake manifold tubes & you will see another grey handle for spark plug number 4. Using needle nose pliers reach in between the intake manifold tubes and twist & pull the spark plug boot off.

Step 36 - Un-hook the spark plug wire from the 1st coil pack. Now pull the plug wire out between / through the intake manifold tubes until it is free from the engine. Careful, go slow feed with your left hand while pulling slowly with your right hand until the wire is free.

Step 37 - Repeat steps 15 & 16 with this plug wire.

Step 38 - Develop X-ray vision & using the flashlight look and see the very tip top of the spark plug. Line up your two 6inch extensions with your spark plug socket on the end and slip it over this last spark plug.

Step 39 - Going slow, remove the last plug. If it drops out once again use your magnetic pickup tool to retrieve it.

Step 40 - Repeat Step 26.

Step 41 - Proceed to replace it with a Bosch Platinum plug & anti-seize on the threads. This is where your X-ray vision is going to be helpful. This last hole is rather hard to see when you have your spark plug socket in place and are attempting to locate the hole. Remember the hole will be further towards the back of the block than the middle. You will eventually find it and without cross threading the plug it will fit and you can tighten it up.

Step 42 - Feed the spark plug wire once again through / between the intake manifold tubes with the coil end first. You will then use your X-ray vision & needle nose pliers to grip the grey handle and re-insert it over the plug.

Step 43 - Finally you connect this last wire to the 1st coil pack and make sure that the clips on all the plug wires are closed with the wires neatly arranged in them.

Step 44 - Make sure each of the spark plug wires are attached to the coil packs and the two clips on each side of the coil packs are snapped beneath the coil pack connection points.

Step 45 - Slap yourself on the back...your done! Go out to dinner to celebrate the money you just saved!

I don' know who is posting this rediculous answer to this plug question, but I worked on dozens of these 8 plug engines, never took more than 30 minutes to change them out, very few intake parts need to be removed, you do need good assortment of hand tools like snap-on, flex head rachet, ball socket extensions and a spark plug socket with a u joint.

User Avatar

Wiki User

โˆ™ 2011-09-13 23:33:02
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: What diameter should an exhaust extension pipe be for a 93 Ford Ranger 2.3 liter?
Write your answer...
Submit
Sign up for more answers

Registered users can ask questions, leave comments, and earn points for submitting new answers.

Already have an account? Log in

Related Questions

What diameter should the pipe be leaving the exhaust manifold on 94 ford ranger 2.3 liter?

two inch


Where can you buy a donut for a Saturn sl1?

The gasket between the exhaust manifold and the exhaust headpipe is often called a "donut". It's a specially designed composite gasket, that can endure the pressure and heat of the exhaust system. Measure the diameter of the headpipe, then you should be able to go to just about any auto parts retailer and request a gasket of that diameter. OReilly auto parts, Auto Zone, Pep Boys and any local auto parts retailer should be able to help you.


How do you write a letter to a judge for an extension?

A letter should be written to the judge if an extension is needed for a court appearance. It should state the date of the court appearance and the reason needed for the extension.


When running an automobile in a closed area you should?

Avoid turning on the car A/C and open the windows to prevent carbon monoxide poisoning.


Are exhaust manifolds covered by warranties?

Exhaust manifolds should be covered by warranties.


What is the diameter of a circle that has a circumfrance of 21.98m?

The diameter should be 7m.


You just went to this website for Winco foods Its asking for an extension What is that for?

its for employment, they should give you the extension.


Should the intake and exhaust valves be close when the?

Yes the intake and exhaust valves have to be close.


Should a dry sauna have a exhaust fan?

A dry sauna does not need a exhaust fan


Common name for raduis?

diameter is a nother name to get radius if you times the diameter bye the length and widht you should get the radiusdiameter is a nother name to get radius if you times the diameter bye the length and widht you should get the radius


Where are the oxygen sensors located on the 1995 cadillac on the converter or what?

there should be one on the exhaust manifold and there should be another one after the catylitic convertor on the exhaust pipe


How do you replace the oxygen sensors on a 96 mustang gt?

The oxygen sensors that connect to the exhaust system. There should be two, and they should screw into the side of the exhaust.


Where is the drain hole be located on a 2000 kia sportage exhaust?

there should not be any drain holes in an exhaust


How do you remove exccess fuel in the exhaust system?

there should not be any fuel in the exhaust system, if there is, you have serious problems


If the wire is increased what should happen to the diameter?

If the length of the wire increases its diameter decreases


Can you use an extension cord with a freezer?

Freezers typically state that they should not be used with an extension cord. This can cause a fire hazard.


What is a marine Ranger?

The Marines don't have Ranger units. Marine Corps personnel, however, can attend the Ranger School. Though, if somebody tells you they were a "Marine Ranger", you should definitely view them with skepticism.


Does a 97 ford ranger have a rev limiter?

it does.my 2.3 ranger has one so yours should


Where is the ranger net in Pokemon Ranger?

It should be on the Title Screen where the 'Continue' and 'New Game' options are located. *If it's not there you will have to complete the game to access the Ranger Net*


Un-fused multiple outlet extension cords should?

should not be used


How does the exhaust from your car get in?

The exhaust gets into the passenger compartment usually by a hole in the body of the vehicle. Another possibility is if there is an exhaust leak at or around the engine compartment,if this is so the ventilation for the passenger compartment can pull in the exhaust. Also you should check that the end of the tail pipe should stick out a little past the bumper.


How to unsubscribe sweetim.com and it should not be seen on google page?

It could be due to an extension installed without your consent. You can remove the extension from the tools.


What is the diameter of a 24 inch pizza?

When advertised the measure of a pizza is its diameter. A 24 inch pizza therefore should have a diameter of 24 inches.


What is an diameter?

A diameter is a line going through the middle of an object. They should be equally parted when you are finished.


What is the diameter of inoculating loops?

The diameter is about 1mm. It should be small enough to hold a drop of liquid.