0
A: TTL Vcc is fixed at 5v +/- .5 volts while MOS can be run at higher Vcc like 12 volts therefore there is a compatibility problem and a converter must be installed between this family of gates to make them compatible with each other. So a converter will do just that translate a TTL level to a MOS level
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Why ttl voltage level converting to rs232 level?
Whwn an IC is connected to a PC, then the voltage levels of these two should be synchronized. For this purpose, the TTL voltage level is converted to RS 232 level. RS 232 is the interface between a PC and an IC.
Why TTL is preffered in case of microcontroller than CMOS?
TTL is preferred in n-mos technology because it produces more heat and thus it's preferable in microcontroller circuit but c-mos does not produce waste heat which is why TTL is not preferred in c-mos.
What are the advantages and disadvantages of N MOS circuits as compared to TTL?
TTL stands for Transistor-Transistor-Logic. N-MOS is a type of a metal oxide semiconductor technology. TTL is faster, but generally uses more power. MOS based devices are slower, they and they use less power. Speed is an issue when dealing with high speed data processing.
What is voltage level of ttl?
Standard TTL (which stands for Transistor-Transistor Logic) circuits operate on a 5V power supply. The typical level for a logical "0" is between 0V and 0.8V, and the typical level for a logal "1" is somewhere between 2.2V and 5V. Typically, a value little lower than Vcc (power source voltage) is used; in case of a 5V supply, this is usually around 4.5V, but TTL devices are built to withstand full Vcc as input, just in case.
What TTL Logic Voltage Level?
Historically, transistor-transistor logic (TTL) voltage levels have been 5.0 volts, with a high being any voltage above about 3.5 volts and a low being any voltage below about 1.5 volts, with lots of variations on the high/low cutoffs from part to part. Since about 2001, however, most processors have been using low-voltage TTL (LVTTL), which has a nominal voltage of 3.3 volts (approx >2.2 volts for high and approx < 1.2 volts for low). Hence, many parts advertised as "TTL" today actually work at 3.3 volts rather than 5.0 volts.
Full form of vcc and vdd in TTL and CMOS?
vcc-voltage collector to collector vdd- voltage deran to deran ttl- transister transister logic cmos - complementary metal oxide same conductor
What are the differences between TTL and MOS logic families?
The biggest difference is the types of transistors used: TTL (transistor transistor logic) uses bipolar junction transistors, MOS (metal oxide semiconductor) uses metal oxide semiconductor field effect transistors.For a very long time TTL operated at much higher speeds than MOS logic, but also used much more power. However several improvements in MOS over time eventually allowed it to operate at higher speeds than TTL could do without consuming so much power that it could not be properly cooled.The actual circuits used to construct logic gates is very different, but these details cannot be addressed on this site.
What is the maximum supply voltage for a 74LS08?
The maximum supply voltage per the data sheet is 5.25 volts. This is a common max for TTL type IC's.
Why rs232 voltage level converting to ttl level?
RS-232 is a standard built a longer while ago, and its specifications dictate a maximum voltage of +-25V. HIGH signal levels at +-5V, +-12V and +-15V are not uncommon. The range of operation is from -25V to +25V. Also, RS-232 standard notes that levels between -3V and +3V are illegal (as in, they are assumed not to exist, nor carry any information). On the other hand, TTL stands for Transistor-Transistor Logic, and the maximum rating for that is 5V. HIGH signal levels are at any point above 3.5V. The range of operation is between 0V and 5V. If one were to connect these with no conversion, the TTL device would probably be burned. Even if it would withstand, the designs are sufficiently different for them not to communicate properly. Thus, the need to 'bridge the gap' between the two.
What is a TTL-compatible output?
Compatibility in TTL means that the output of one TTL device can be used to drive the Input of the other TTL device , This because the low and high output window fit inside the low and high input window/profile TTL stand for Transistor Transistor Logic, so any voltage between 0 and 5 volt is compatible where any voltage between 3V and 5V is logic 1 and zero volt is logic 0
What is a TTL compatible output?
A: TTL gates operates on the premise of having +5 dc on the rail therefore the output will be in the range +5 volts. A cmos gate while similar to a TTL function is not really compatible since the output volts can be 12 volts or more. Besides that TTL gates require some input current for it to operate
Why do you connect capacitor in MAX232?
The input to the max232 ic will be of Transistor Transistor Logic (TTL) and its voltage range will be of 5 volt. The output of the max 232 ic will be of Recomended Standard 232 Logic (RS232 logic) and its voltage range will be of 12 volt. The max 232 ic which is operating on 5 volt supply has to step up the 5 volt input to 12 volt. Hence a capacitor is used for pumping the voltage and called as pumping capacitor.
