0
Its is the emiiter base of the transistor voltage!
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is an emitter follower?
This is a particular transistor amplifier configuration. In general, the input signal is applied to the base, the collector is connected to a supply voltage, and the output is taken between the emitter and power supply common. One of the characteristics of the emitter follower is the output voltage "follows" the input, but the output is reduced by the Vbe voltage (the voltage drop between base and emitter, approximately 0.7 V for a silicon bipolar transistor).
What is emitter biasing?
Emitter biasing is when you add a resistor between the emitter of a transistor and the 0v rail so that any voltage developed across the emitter will subtract from the voltage on the base and effectively turn the transistor OFF. We are talking about an NPN transistor and the transistor is an "ordinary transistor" or BJT (bi-polar Junction Transistor). For more information on transistor biasing see: Talking Electronics website.
When testing transistors how much minimum voltage difference should be seen across the base-emitter junction?
It depends on the transistor. Minimum base-emitter junction voltage can be as low as 0.6 volts for a silicon transistor, and as low as 0.2 volts for a germanium transistor.
What is the working of a transistor?
For proper working of a transistor,the voltage at the base region must be more positive than that of the emitter region.The voltage at the collector region, in turn, must be more positive than that of the base region.when voltage is applied to transistor, the emitter supplies electron,which is pulled by the base from the emitter as it is more positive than the emitter.This movement of electrons from emitter to collector creates as flow of electricity through the transistor.The current passes from the emitter to the collector through the base.Thus, adjustment of voltage in the base region modifies the flow of the current in the transistor by changing the number of electron in the base region. In this way, small changes in the base voltage can cause large changes in the current flowing out of the collector. We have three transistor element, a.)Emitter b.)Base c.)Collector
What is the purpose of a transistor in a circuit?
A transistor has three leads, called the base, the collector, and the emitter. The voltage of the base (in relation to the ground) determines whether and how much current flows from the collector to the emitter. An NPN transistor can be off, meaning that there is no (or very little) voltage from the base; partly on, meaning that there is some voltage from the base; or saturated, meaning that it is receiving full voltage from the base. A saturated transistor allows the current to flow from the collector to the emitter unopposed; a partly on transistor provides some resistance; and a transistor that is off provides full resistance. A PNP transistor is similar to an NPN transistor except it performs the opposite function: when it is saturated, the current is fully resisted; when there is no voltage from the base, the current is not at all resisted; and when it is partly on there is some resistance. In sum, a transistor controls the flow between the collector and the emitter based upon the voltage of the base. this is carbage. a transistor is basicaly two diodes back to back base being common TO BOTH DIODES because of inpurity doping on purpose at the depletion region the transistor will control the current flow on the other diode. Once it reaches saturation both diodes conduct therefore current can flow in BOTH DIRECTIONS ACROSS IT.
What are the function of the transistor?
A transistor has three leads, called the base, the collector, and the emitter. The voltage of the base (in relation to the ground) determines whether and how much current flows from the collector to the emitter. An NPN transistor can be off, meaning that there is no (or very little) voltage from the base; partly on, meaning that there is some voltage from the base; or saturated, meaning that it is receiving full voltage from the base. A saturated transistor allows the current to flow from the collector to the emitter unopposed; a partly on transistor provides some resistance; and a transistor that is off provides full resistance. A PNP transistor is similar to an NPN transistor except it performs the opposite function: when it is saturated, the current is fully resisted; when there is no voltage from the base, the current is not at all resisted; and when it is partly on there is some resistance. In sum, a transistor controls the flow between the collector and the emitter based upon the voltage of the base. this is carbage. a transistor is basicaly two diodes back to back base being common TO BOTH DIODES because of inpurity doping on purpose at the depletion region the transistor will control the current flow on the other diode. Once it reaches saturation both diodes conduct therefore current can flow in BOTH DIRECTIONS ACROSS IT.
What is vce and ie of a transistor?
A: Vce is the voltage across the transistor . Ie is the emitter current. Ico is the collector current with the base open. Or really the leakage.
What does the electronic term Vb mean?
Base voltage in a transistor. There is also Vc (Collector voltage), Ve(Emitter voltage), Ic(Collector current), Ib(Base current), Ie(Emitter current), Vcc(Supply voltage), and Hfe (Forward current gain)
What are the parts of a transistor?
The emitter, the base, and the collector are parts of a transistor.
What is the difference between common base emitter transistor and common base transistor?
Common base transistor if the emitter is open current Ie=0 but a small collector current thus exist.this current is reversed biased collector to the base voltage it is represented by Icbo while common emitter is d base terminal is open circuit and the base junction is reversed biased current Icbo flow from the tcollector to the emitter in the external circuit this current is called leakage current.
Is a diode like a transistor?
No. A diode is not like a transistor, and a transistor is not like (two) diode(s). Taken in isolation, the emitter-base and collector-base junctions of a transistor appear to be diodes, but they are coupled together so that the base-emitter current affects the collector-emitter current.
What should be the value of collector current in terms of DC gain if transistor is in saturation mode?
DC current gain is collector-emitter current divided by base-emitter current. In linear mode, gain is beta, or hFe. In saturation mode, however, the transistor is over-driven and you can no longer relate collector-emitter current to base-emitter current. The transistor operates like a switch, and collector-emitter current is a function of voltage and load impedance only. (Ignoring the relatively small voltage drop.) To maintain saturation mode, the collector-emitter current must be smaller than the base-emitter current times hFe. Often, it is several times smaller, because hFe can vary from transistor to transistor, and your design must account for this variability.
