0
What is the pulley that is before the harmonic balancer on a 93 Toyota 4runner?
Wiki User
∙ 14y ago
Crankshaft Pulley !
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you remove the harmonic balancer in a Nissan Maxima?
To remove the harmonic balancer from a Nissan Maxima, first you need to removed the center bolt. After that, you can use a puller to remove the harmonic balancer. Before you do this, make sure you disconnect the battery and remove the drive belts.
Why wont harmonic balancer pull off 1986 ranger 2.9 with puller you have sprayed with PB blaster?
There is a front pulley, a center bolt and washer AND a spacer behind the washer that has to come off before putting on the puller. I didnt know this and tried to pull balancer, this spacer is pressed in or it was after i tried to pull balancer off over it !
How far can you drive with harmonic balancer removed?
You didn't state what vehicle you have but with most vehicles all the belt driven accessories are driven by pulleys attached to the harmonic balancer so you will be driving without a functioning alternator, power steering pump and water pump not to mention you will probably be splashing out motor oil profusely. I give it about 20 to 30 minutes before the engine seizes.
Where is the location of the crankshaft sensor for a 1995 Toyota Corolla?
it sits right behind the harmonic balancer. you have to remove it so you can replace the sensor. here,s a tip for you. before removing the sensor mark around it so you can put the new 1 on in the same place as the old 1 was. don,t forget to unhook the battery.
Harmonic balancer on a 1996 Chevy s 10 blazer do they warp?
No they do not. If you look at it real close you will see that it has a piece of rubber between the 2 steel parts that make the balancer, the rubber has sliped / worn out. The balancer is made of 2 pieces of steel with rubber in between them. REPLACE BALANCER. Before you take it apart make sure that the pulley that is bolted to it is not on crooked are bent. May just need a pulley put on it.
Where is the back up light switch for a 91 Toyota 4Runner?
It's right in the transmission, rear top portion before the propeller shaft..
My 95' 305 vibrates at freeway speeds?
Before looking at engine possibilities, check the tires, suspension components, and universal joints. If all is well, check the harmonic balancer to see if the elastomer has worn out.
How do you install a harmonic balancer on a Buick Century?
I just use the crankshaft bolt to squeeze it back on. Just line up the groove in the harmonic balancer to the key in the crankshaft and slip it on until it's snug. Screw in the crankshaft bolt and tighten it down. The more you tighten, the more it will push the harmonic balancer. Warning! The crankshaft bolt must screw in freely at least five or six turns before you can begin tightening it. If the bolt ain't long enough then you will have to find one the same size, but just a little longer or you could face an unholy nightmare if you strip the bolt out. Use the long one if you have to to get the balancer pushed on a bit. Then, switch back to the original bolt and finish tightening. Good Luck and Good Day!
What is the timing for a 1967 Chevy impala sports coupe?
4 degrees btc-before top dead center with the vacuum spark line disconnected.the timing mark location is on the harmonic balancer. this is for a 327 engine
Where is the oil pressure sending unit on a 2000 Isuzu Rodeo 3.2L V6?
It is on the oil cooler manifold, next to the oil pressure switch.look front of engine below harmonic balancer,before oil filter.
1991 cutlass cruiser 3.3l harmonic balancer replacement?
Kent-Moore has a special tool for this purpose. Failing that, you can use a three-bolt puller, but do NOT completely unscrew the balancer pulley bolt before using the 3-bolt, just loosen it up a bit. The Kent-Moore tool works with the bolt removed.
How do you find the adjustment on a 2.9l ford engine for timing?
Well to begin with, it all depends on where you live. For example, if you live in Colorado the timing should be set to 10 degrees before top dead center (BTDC). First, there is an in-line spout connection. It looks like a jumper plug. Unplug that connector. Then get a timing light, one with an advance dial, and set the dial at 10 degrees, and "shoot" it at the harmonic balancer. On the 2.9L V6 the timing marks are on the harmonic balancer. There is an arrow that sits over the harmonic balancer on the passenger sider of the engine. Locate it and "shoot" your timing light at it. If the timing light is set at 10 degrees, then the number on the harmonic balancer should look like this TIC. That means you're timing is right on the money. If it doesn't then loosen up the distributor hold down clamp and turn the distributor until it goes to TIC. Hope this helps. Clay Colorado
