0
What is the purpose of a grab ring on a push fit plastic fitting?
Wiki User
∙ 15y ago
The grab ring is what physically secures the tubing inside the fitting by biting into the tubing. The angle of the grab ring teeth causes the "bite" to be greater as the tube pressure or load increases, up to a point. At some point, the grab ring will usually bite off the tube or the grab ring will invert, allowing the tube to become disconnected.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you change front indicator bulb proton persona 1997?
Inside the bonnet at the rear of the indicator light fitting is a steel ring. This is a clip-in spring fitting. Once unclipped the indicator unit slides out. The bulb is attached by a simple push on fitting.
When you bend your thumb it pops?
Relax your hand. put your other hand upside down in between your thumb and hand and grab your thumb pull back the hand with the tumb you want to pop
What exercises do astronauts do?
There are several exercises that can be done in zero-G, any of which you can do here on Earth. "Isometric" exercises, in which you use one muscle in opposition to another, require no equipment and can be done anywhere. Here's an example; press your two hands together. Push HARD. Relax. Push; relax. This is an "isometric" exercise, meaning "same movement". Here's another; Place your left hand on the inside of your right knee, and the right hand on your left knee. Use your arms to push your knees apart, and use your legs to pull them together. Or, reach down and grab your chair, and PULL yourself down into the chair. (Please DO NOT do this one in the seat of a fighter jet, as you might accidentally grab the alternate ejection seat handles!) Other exercises that can be done on Earth or in zero-G involve flexing against a bungee cord or large rubber band, or using a resistance device like a rowing machine or a stationary bike.
What is the purpose of a measuring wheel?
A surveyor's wheel, also called a clickwheel, hodometer, waywiser, trundle wheel, measuring wheel, or perambulator is a device for measuring distance.
Is natural disaster push or pull factor?
earthquake
How do you remove the quick connect on the transmission line of a Chevy s10?
There is a plastic fitting or tool that goes around the line and you push into the fitting to release it. Push it in and pull out the line. You can buy a set of 5 for around $8 to $10 U.S.
How do you disconnect a fuel line on a 2002 ford expoler?
Ford uses a quick connect fitting. You need the right size plastic release clip for the size line. It is a split plastic washer that goes around the line, you push it into the fitting and that releases the line. You can get a set of them for I think $6. Once you see the tool, it should make sense what it does and how to do it. Push the clip into the fitting with one hand and pull the line out with the other.
How do you remove heater hose on top of intake94 350 enginethere is a fitting and clips?
push in on sides of the plastic clip both sides at same time
How do you remove the hydraulic fitting on the transmission of a 1999 Chevy S-10 with the manual VN1500?
You need to pinch the plastic sleeve and push from both sides 180 degrees. In then releases the entire connector and plastic hose. (black)
How do you adjust a 1997 Honda civic emergency brake button?
Take both hands and grab the plastic cover around the handle that the button sticks out of. Push down the cover. The button will appear.
Adjust handbrake on vectra c?
It is very easy to adjust the handbrake on a Vectra C. All you need to do is remove the rear console and release the handbrake. Under the handbrake is a cable with a white end fitting, push down the end fitting onto the plastic locking device. Then pull the lever and it will be adjusted.
If your friend hits you in the face?
depends....if they hit you hard, then you grab there face and push it into a wall and make them say sorry only if it was on purpose thow but if it wasnt then just make them say sorry nicely. (:
How do you remove a brass fitting from a galvanized fitting?
Two pipe wrenches. One to hold the galvanized from turning and one to turn the brass fitting. Pull on one and push on the other and it should come out.
How do you remove hydraulic clutch line 95 ford ranger manuel?
on the side of the trans where the slave cylinder goes into the bell housing, there is a gold fitting attaching the hyd. line to the slave. on that gold fitting there is a white plastic band that needs to be pushed down towards the slave cylinder. push it in far enough and the line will pull free.
What is a hose nipple?
A hose nipple is a push-on fitting that allows you to connect the hose to a threaded fitting. See related link below for a picture of a hose nipple.
1990 2.9 ranger fuel pressure regulator looks to have a non serviceable fitting do you need new fuel line?
I'm assuming its the black cylinder type fitting that doesn't twist/pull/smash/bash/tear/run over with the truck come off...lol What you need to do is look on the very top of the black cylinder under the regulator and there will be 2 small square holes. Now I wasn't able to find the actual tool that goes into these two holes to push down on the fitting INSIDE of the black cylinder thing, which I assume was buried with henry ford... Heres what you have to do and WHAT I ENDED up doing. Inside of the cylinder is a push down fitting, basically like an impact drill has, quick connect fitting, to attach fittings to the drill, and what you have to do is push 2 things down into the holes and push down on the fitting inside the cylinder to release the regulator. Now how you do that I have no idea. What I did was accidently brake the top of the black cylinder off (just plastic) to expose the push down tab thing itself, so I then just push it down by hand and pulled the regulator right off. I HATE that fitting; I could never get it off or find help with it, so I would just buy used regulators with the stock hose still connected and of course they would fail. Hope that helps man
Where is the PCV valve located on a 1991 Chevy Cavalier?
I have a '91 RS with a 2.2 4 cyl engine and came across the pcv valve by accident- it is inside of the valve cover. Look at the top of the valve cover on the passenger side. There will be a hose- one end goes to the intake manifold and the other to a plastic fitting (with a nut) on the vlave cover. Take off hose and unscrew plastic fitting. Fitting will have 3 prongs on it and a "O" ring. Take needle nose pliers and reach into the valve cover to pull out the pcv valve.There should also be a "O" ring on the pcv valve which holds it into place. Put "O" ring on new valve and push back in by hand- you will feel it "snap" in. Screw back in plastic fitting and connect hose.
