Chevy Malibu
Chevy S-10
Ford Ranger XL
Chevy 350

What is the rocker arm torque settings for 2001 Chevy Malibu 31 liter?

101112

Top Answer
User Avatar
Wiki User
2009-07-30 18:19:19
2009-07-30 18:19:19

step--1----1997-89in lbs,------1998 and later----168in lbs,----step2---rotate an additional 30 degrees.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

No, head bolt torque is much higher than rocker arms.

User Avatar

what is the torque on 2.2 rocker arms and in what order

User Avatar

I need head bolt torque specs and sequence on 2003 Chevy Malibu 3.1

User Avatar

what is the torque setting for the head bolts on a 2007 chevy malibu with a 2.2L engine

User Avatar

torque especifications for Malibu 1999 3.1 engine

User Avatar

i need to know what the torque specs are on the rocker arms for a 97 Chevy lumina, 3.1L v6

User Avatar

The torque specification for the rocker arm nut on a 1997 Chevy Cavalier is 22 foot pounds. This is the equivalent of 30 newton meters.

User Avatar

Rocker arms are set to a specific preload or backlash on v8 Chevies. There is no torque specification.

User Avatar

The correct torque for the rocker arm bolt is 14 Nยทm (124 lb in) plus 30 degrees.

User Avatar

The 2000 Chevy Impala 3.4 liter engine rocker arm bolt torque specification is 45 pounds. The rocker arm bolts should be torqued in 15 pound intervals.

User Avatar

I need the torque and secuense for the hea d bolts for a Chevrolet Malibu 2000 3.1

User Avatar

what is the torque specs to a 2002 Chevrolet Malibu 3.1 liter motor. Need head and intake torque specs. and sequence.

User Avatar

For the 1989 Chevy S-10 with the 2.5 liter engine, the torque setting for the rocker arm bolt is 22 ft. lbs. The torque setting for the rocker arm cover is 75-inch lbs.

User Avatar

Rods and Rocker arms were the problem with my Malibu after changing lifters

User Avatar

The lower intake is 10 ft lbs the upper is 18ft lbs. If you go to autozone.com and read there specifaction area its listed there. That's were I found it!

User Avatar

what is my torque specifications for my 2005 aveo 1.6l

User Avatar

A lot of manufacturers use a torque setting, but not Chevy. With the motor running, go to zero lash, and then 1/2, to a full turn from there.

User Avatar

there is no torque on the oil filter!! when putting back on tighten the filter hand tight as much as you can.

User Avatar

1998 and later--168 in lbs, for rocker arm bolts. step 2 rotate an additional 30-degrees, 3.1 engine,

User Avatar

The lug nut torque specs on a 2006 Chevy Malibu is 100 foot pounds. Although that is the factory setting, most service tire shops will tighten to the universal specifications of 90 foot pounds.

User Avatar

89in lbs and then an additional 30 degrees


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.