0
What is top dead center on compression stroke on a Z24i engine?
Wiki User
∙ 15y ago
db
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Firing order diagram for 1986 Nissan pickup z24i engine?
1324
Where can you get a vacuum line diagram for 1988 Nissan z24i?
The vacuum line diagram for a 1988 Nissan Z24i can be found in its maintenance manual. It can also be found in the cars repair manual.
What is the plug gap on a 87 Nissan d21 z24i?
.032
What type of engine is the 1983 Datsun pickup?
4 Cyl engines through to 1990. Engine ID # is stamped on a pad on the right side of the engine block except for the Z24i which is on the left. Most engines are the Z22, 4 cyl, with 8 spark plugs.
Where is the PCV valve on a 1987 Nissan hardbody Pickup Z24i engine?
On a 1987 Nissan Hardbody Pickup, the PCV valve is located between the alternator and the oil filter. The valve can be seen when the oil filter has been removed.
Will 1 1987 transmissionand transfer case with a z24i interchange with a 1992 with a ka24e both are Nissan pickups with 4-cylinder?
Yes.
What the fuel pessure should be for an 1987 Nissan pup z24i?
It should be check after the fuel filter and it should be approximately 37 psi.
What is the vacuum hose routing diagram for a 1986 Nissan pickup with a 2.4 4x4 with 5 sp trans z24i engine d21?
Try this link that I just found... http://nissannut.com/projects/z24i_fuel_injection/ I just found this about five minutes ago. I also have the same problem. I think it will help. theharemguy@gmail.com
What are the head bolt torque specs for 1987 Nissan d21?
For the Z24i and KA24 engines, the "cylinder head to front cover" torque specification is 3 to 8 foot-pounds (or 4 to 10 Nm)
What is the firing order for a 1980 Nissan pickup?
For the Z24i inline 4 cylinder 2.4L the firing order is 1-3-4-2 If you have the V6 if they had one it will be 1-2-3-4-5-6*1
Where is the location of the PCV valve 1987 in a Nissan pickup?
As a matter of fact, I just replaced mine a couple weeks ago. If you have the z24i, it will be located on the side of the crankcase. With the air cleaner removed, look down between the intake and the valve cover, there will be a hose that plugs into the block. Pull the hose off an voila! there's the PCV valve. Good luck! ~Lizzard
How can you change a 1985 Nissan 4X4 720 truck from carburetor to fuel injection?
1985 NISSAN/DATSUN PICKUP 2.0L 4-cyl Engine Code Z20or1985 NISSAN/DATSUN PICKUP 2.4L 4-cyl Engine Code Z24You maybe able to locate a Z24I engine that you could get the needed parts from if you have the Z24 engine.Also try contacting these people they maybe able to help.http://www.4x4parts.com/public_html/shop/index2.php3?page=shop/index2or perhaps someone on this forum could also help with Detailshttp://www.mississippi-mud.com/forums/FYI:If she starts acting funning in the cold weather and only on long drive 15+ miles like on a highway, no stop an go stuff an not wanting to maintain speed. An you pull over rest say 5 minutes then goes good again for a bit and starts losing speed again. Check your exhaust pipe if it is not 100% open (ie no kinks) that is most likely your problem. It was for for my 86 1/2 which is now a trailer.Hope This Helps and Good Luck.
