0
The exhaust manifold for an E250 is usually sold as a complete kit. The nut is a standard issue, and is between the a half inch and a full inch diameter.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
Nut size for exhaust manifold 94 pathfinder V6?
not sure........nissan part # 08918-2081A
Where is the 02 sensor on a mk3 fiesta?
Look on top of the exhaust manifold. there should be a big nut with wires going into it. Hope this helps
Where is exhaust back pressure sensor on 2006 6.0 diesel ford f350?
The exhaust back pressure sensor on a 2006 6.0 diesel Ford F3 50 can be located near the exhaust manifold. The sensor is a probe that can be removed by loosening the nut.
What to fix exhaust pipe at manifold car bottomed out and the exhaust pipe came off the manifold bolts still looks like there is a rusted nut on the end of bolts but flange goes past nuts?
Cut the bolts off and you will have to purchase a new flange kit from any parts store.
What are the torque specs for BMW E36 exhaust manifold?
20 NM (15 lb-ft) for the nut on the exhaust nut-to-head-stud. Good luck getting a torque wrench on each and every one. Expect to rely on your 11 mm offset wrench and your gut-torque-meter.
1989 Chevy Astro Van has a coolant leak at the fitting were the heater circuit pipe attaches to the intake manifold near the distributor How does this fittings come apart?
It snaps in. But before you snap it out, take the nut out that holds the pipe to the exhaust manifold.
Exhaust flange bolt size on 1999 Chevy S-10?
The nut should be a 15mm, the stud, I'm not sure.
How do you remove a broken exhaust manifold bolt from a 2006 Jeep Commander?
The first step is to remove the manifold. If the bolt is sticking out, remove with a vise grip pliers or stud remover. If broke off flush, drill and extract with an easy out or try to weld a nut to it and turn out that way.
Where is the oxygen sensor located on a 1994 Oldsmobile Achieva?
in the exhaust system Very close to the manifold, you should see a wire come out of a large nut, to remove and replace you should have a socket made for this application
Lug nut size on Nissan 240sx?
The lug nut size for a 240sx with a four lug pattern is 10x1.25. The lug nut size is 12x1,25
How do you take off tensioner pulley on 2000 grand voyager?
There is one 15mm nut on the back side of the tensioner. You have to get at it from under the vehicle. It is just below the end of the exhaust manifold. It is fairly easy if you use a long extension and a flex socket.
Where is the egr valve sensor located on a 2000 ford e250 4.2l v6?
4.2L, 4.6L, 5.4L and 6.8L Engines 1. Disconnect the negative battery cable. 2. Remove the vacuum hose from the EGR valve. 3. On the 4.6L engine, remove the nut and brake booster bracket. 4. On the 5.4L engine, remove the DPFE sensor retaining nuts and place the sensor to the side to allow access to the EGR tube. 5. Disconnect the EGR valve-to-exhaust manifold tube from the EGR valve. 6. Remove the EGR valve mounting bolts, then separate the valve from the intake manifold. 7. Remove and discard the old EGR valve gasket, and clean the gasket mating surfaces on the valve and the intake manifold. To Install: 8. Install the EGR valve, along with a new gasket, on the manifold, then install and tighten the mounting bolts. 9. Connect the EGR valve-to-exhaust manifold tube to the valve, then tighten the tube nut to 25-35 lbs. (34-47 Nm). 10. Connect the vacuum hose to the EGR valve. 11. On the 5.7L engine, install the DPFE sensor. 12. On the 4.6L engine install the brake booster bracket and the retaining nut. 13. Connect the negative battery cable.
