0
22mm
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
What size socket wrench must you use to replace tires?
The size that fits your wheel nuts. -There are only 4 basic sizes, it can't be that difficult to figure out !
1999 Ford Explorer that ABS light kepts staying on sense you put new tires on?
are the tires the right size, and all the same size, how many did you replace, is it AWD, are they inflated correctly, did you break a sensor taking off or putting on the tires
What is 1.6 crop factor for aps-c sensor dslr cameras?
The crop factor indicates the size of the sensor. It is relative to the size of 35mm film, also known as Full Frame. Actual size of Full Frame is (36mm x 24mm) To calculate the sensor size you use: [(1 / crop factor) * Full Frame] = [(1 / 1.6) * Full Frame)] = .625 * Full Frame = 22.5mm x 15mm This is very close to the actual size of the APS-C sensor. (23.7mm x 15.7mm)
Why would a taillight fuse keep blowing?
You might check the Amps size of the fuse. A lot of times, if you are using a fuse with too little Ampage, it can cause the fuse to blow. Your owner's manual should tell the proper size of fuse for that specific circuit.
How do you change a fuel rail sensor?
Do you mean fuel pressure sensor? If so please post year, make, model and engine size.2004 mercury monterey.{dont know engine size}
How do you replace a crankshaft sensor on a 1991 Buick Century?
Haynes repair manual available from www.amazon.com. Not hard. Locate sensor, unplug electrical connector, use socket of appropriate size, remove.
What size socket to remove a 2001 Nissan Quest axle hub nut?
It takes a 1 3/8 socket. That is one and three eights.
What size socket do I use to replace a spark plug on a 2003 escape?
5/8" peanut plug socket
How do you replace oxygen sensor on a 1996 Chevrolet Astro Van?
oxygen sensors are located on the exhaust pipe, after the header. a metal cylinder screwed into the pipe with 2 wires attached. safest way is to purchase an o2 sensor socket for your 3/8 ratchet. it is the appropriate size deep socket with a slot in the side for the wires to go.
What size socket wrench do you need to replace 2005 Nissan maxima brake pads?
14 or 17 mm socket.
How do you replace a knock sensor for an acura tl 2000?
Disconnect the negative battery cable.Drain the engine coolant into a suitable container.Unplug the sensor connector.Using the proper size socket, loosen and remove the knock sensor.To install:Carefully thread the sensor into the engine block.Tighten the sensor.Attach the sensor connector.Refill the engine coolant.Connect the negative battery cable.
What size socket will BE needED to replace a harmonic balancer on a 1998 Malibu?
15mm
How do you Replace oil pressure sensor on a 2003 jeep grand Cherokee?
Answer: Located under the vehicle by the crankshaft pulley and oil pan. The sensor basically screws in the block and should have an o-ring that seals oil from leaking. I believe the size is either 20 or even 22mm socket and has to be a deep socket to fit over the sensor to the nut. Be careful not to damage plastic plug in part of the sensor when tightening. Also has a two prong connector use a flat head to unplug and remove and replace sensor do not over tighten just nice and snug will do.
How do you replace the oil pressure sensor on a 2003 jeep grand Cherokee?
Answer: Located under the vehicle by the crankshaft pulley and oil pan. The sensor basically screws in the block and should have an o-ring that seals oil from leaking. I believe the size is either 20 or even 22mm socket and has to be a deep socket to fit over the sensor to the nut. Be careful not to damage plastic plug in part of the sensor when tightening. Also has a two prong connector use a flat head to unplug and remove and replace sensor do not over tighten just nice and snug will do.
What size socket is needed to replace the rear brakes pads on a 2001 Sportster XL 883?
A twelve point 1/4 inch socket.
How do you replace a camshaft sensor on silverado 1500?
Need to know the year and engine size.
Where is the O2 sensor located on a 2002 CRV How hard is it to replace it?
THERE ARE TWO SENSORS ON THE CAT. RIGHT AFTER THE HEDDER. YOU WILL PROBABLY NEED A SPECIFIC SOCKET FOR THE SENSOR (SLOTTED) OR GET THE EXACT SIZE "BOX" WRENCH BECAUSE OF THE RIBBS ON THE CAT. TEND TO INTERFERE WITH ANY OTHER TYPE OF WRENCH. !!!!!!!!!IF YOU ARE GETTING THE P420 CODE, IT IS MOST LIKELY THE CAT AND NOT THE SENSOR...BEEN THERE DONE THAT.
