Ford Probe
Saturn L-Series
Toyota Camry
Timing Belts and Chains

What tools do you need to replace the timing belt on a 1993 Ford Probe 2.0l and how do you do it?

575859

Top Answer
User Avatar
Wiki User
2004-12-10 06:17:38
2004-12-10 06:17:38

The question you ask is too involved for a proper answer. You need to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Replace the chain and both the cam and crankshaft gears.

User Avatar

install timing belt on 1993 Plymouth sundance

User Avatar

Same ones for a timing belt replace. Once the timing belt is off, the center crank gear just pulls off, and the outer cam gears pull off once the single center bolt is removed.

User Avatar

Replace the timing belt and pray that you dont have bent valves.

User Avatar

diagram of starter in a 1993 ford probe

User Avatar

the water pump is located under the timing belt cover. in order to replace it you need to remove the timing belt, i would recommend doing the timing belt while your in there too.

User Avatar

If you need ask how to do this then you need to take it in and have it done. there are certain tools you need to do this type of repair. And it can be time consuming if you dont what you are really doing. Also the should change water pump too when doing this timing belt.

User Avatar

Possibly, but u have to remove the timing belt to get to it. If you are going to replace the water pump u might as well change the timing belt also being that they are in the same area and the job is time consuming.

User Avatar

The engine in the Mercury Villager does not use a timing chain, it uses a timing belt. The recommended belt replacement interval is 105,000 miles.

User Avatar

Replace every 60,000 miles. need picture diagram of 2.3 4cyl ford ranger 93 timing belt diagram

User Avatar

it is located on the passenger side of the car behind the water pump and timing belt and sprockets. its a tough job

User Avatar

Replace the cam belt every 60,000 miles.

User Avatar

How do you adjust timing chain on a 1990 sentra?

User Avatar

Take it to a garage as you need special tools and the alignment has to be set when you replace them.

User Avatar

Get the Haynes manual for the vehicle. It goes step by step. Used it for mine.

User Avatar

its a Mazda engine . ( DOHC 4cyl. 16 valve 2.0l ) For the probe 1993

User Avatar

how do you line up timing chain on a 1993 sl1

User Avatar

Yes it's difficult and you need a couple of special and expensive tools.

User Avatar

Yes it is possible with a bellhousing adaptor plate..... but in short no......Buy the right tranny......or a flux capacitor......

User Avatar

ford probe gt rims are 7 inch

User Avatar

An Escort water pump is located under the timing cover and is driven by the timing belt. Jack up the right front corner of the vehicle, remove the following: RF wheel, front motor mount, serpentine belt, belt tensioner crankshaft pulley, timing cover, and timing belt, to gain access to and replace the water pump. It is recommennded that you install a new timing belt when you replace the water pump.

User Avatar

Roughly $800.00 parts & labor. This figure could easily double if done by a dealer.

User Avatar

The timing chain for a 1993 Ford escort is located on the front of the engine. It is under the timing chain cover.

User Avatar

How do you disconnect the Data Port when setting the timing on a 1993 Toyota Corolla?


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.