0
Where are the ignition timing marks on a 1991 190E 4 cylinder you don't see a harmonic balancer Thanks?
Wiki User
∙ 15y ago
there is only one mark and one pointer
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Where is the crankshaft sensor located on a 1991 Buick LeSabre custom?
to my knowledge it is located behind the harmonic balancer. You should be able to c the wires runing to it just to the right of the harmonic balancer. Now if you could help me with information on how to uninstall the harmonic balancer i would greatly appreciate it Thanks. To remove the harmonic balancer you have to buy or rent a harmonic bancer puller. The bolts required for yours may not be included. If not you will have to go to the hardware store and purchace them. You should use the 3 1/2 inch #8 1/4 inch bolt 3 required also buy 3 washers cost under 4 dollars.
What does a P 1345 diagnostic code mean on a 1996 Mazda 626?
My '96 Mazda 626 broke its harmonic balancer. With it broken, it would start and run fine. I replaced the balancer and belts and tried to start it. After much cranking, it started but died and wouldn't start again. My scanner indicated code P1345 "Manufacturer controlled ignition system or misfire." It also had a code P0302 "Cylinder 2 misfire." That tells us what the code means, but what does it really mean? Where does the problem lie? Help would be appreciated. Thanks.
Your bronco is leaking oil from the front of the truck what could be the cause of this problem it lost oil pressure and when you got home oil was leaking from the front please help thanks?
you need a front oil seal and u need take the pulley off and the harmonic balancer off to change it
Replaced 2001 Saturn sl1 ignition cylinder twice oem still can not go back past accessory or it locks takes forever to play with the wheel and jiggle key to move it whats next thanks?
When the cylinder was replaced, did you get new keys for it also? Using a worn key has this type of symptom regardless of the cylinder.
Who has got a copy of a Wheel balancer FMC 4200HS?
there, thanks for answering. Can you get me a copy of the user manual please? Gretings Ad LBS
Williams wall furnace parts?
hello thanks for welcoming me can i install an electronic ignition in a wall furnace that is standing pilote thanks jean
95 ford thunderbird 3.8L Trying to set the timing can anyone tell me were the marks are I see nothing on the balancer thanks?
Timing is computer controlled.
What exactly is a Dyson cylinder?
The Dyson cylinder is a cylinder vacuum, a vacuum that has better maneuverability, storage, and suction thanks to Dyson's innovative, patented ball technology.
Removing a harmonic balancer on a Nissan 300 zx 1989 Without shop air. How to lock the crankshaft from spinning while loosening the harmonic balancer center nut. Thanks guys?
Answer:Unlike the Honda/Acura vehicles for which they make a specific crank pulley holding tool, on the Nissan VG30 engines pretty much the only (and best) way to remove the harmonic balancer is by wedging a pry bar between the flywheel/driveplate teeth to prevent the crankshaft from turning while you loosen the crankshaft bolt. In order to get that pry bar wedged in, you'll have to remove the two starter mounting bolts, and just push the starter out of the way. To loosen the crank bolt, it helps if you have a nice long 24" flex handle (breaker bar). It also helps if you have an assistant to hold the pry bar and keep it wedged in between the flywheel teeth at the right angle so you should then be able to give that breaker bar a good impact. Good luck! A easy way to remove a Harmonic Balancer nut even on a light truck is to use the starter motor! Put the socket and bar on the nut and check the direction of rotation of the engine, make sure you have it the right way around or it could swing right around and do damage, you want the end of the bar to be resting on the garage floor, keep your hands out of the way and touch the starter motor, Bingo! it`s undone!!!!
How do you check ignition switch in a 1998 Toyota 4-Runner?
I have the same problem, going to have a locksmith make sure its the ignition switch and cylinder and just not a key problem or a tumbler problem.
How do you change the ignition lock dashboard mount in a 1979 F100 keys are lost?
Go down to the local Advance Auto and pick up an ignition switch #S77($13.48) and a ignition lock cylinder #LC14($5.93). With a little work and a whack on the counter the cylinder will go into the switch. (Thanks for helping, Eric!) Back home, use a slot screwdriver and a hammer (there is actually a tool for this I'm sure) to remove the retainer for the ignition from the dashboard. When it comes off the switch is loose. Drop it out from the dash and remove the plug. Plug in the new switch/cylinder setup, slip it into place in the dash and spin the retainer back on. It will probably require the help of another person to hold the switch in order to tighten the retainer down so the switch doesn't spin as you once again use the slot screwdriver and hammer.
Renault clio toque settings for cylinder head?
hi clio 14 rt 97 have you got the cylinder head toque setting for this car thanks
