answersLogoWhite

0


Best Answer

the thick cable goes to the battery positive terminal . one thin wire goes to ignition switch

User Avatar

Wiki User

15y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Where do the wires from a starter go on a 89 suburban?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Art & Architecture

What is the shape of the Start Relay of 1995 Plymouth Acclaim Sedan Auto?

The Starter relay for Acclaims are located right on the starter, its what the wires that go to the starter hooks to.


How do you change a starter on a suzuki aerio?

The starter is located behind the engine . First take the wires off the solenoid, then take the two bolts that go through the bell housing into the starter off and the starter will come out. Place back on mount, put bolts back on and hook wires and hose back up.


Starter wont disengage when you start 93 ford ranger.changed 2 starters and solenoid.where to go from here?

I'd check two things: I don't remember what year Ford changed over, but if yours still has the starter solenoid on the fender, make sure you haven't crossed the small wires. If the solenoid is on the starter, are you certain that you've wired the starter right? There are a couple small wires that connect to the starter,if you connect them wrong it could the cause problems you describe. If you're CERTAIN that the starter and/or solenoid are connected properly, start looking seriously at the ignition switch.


How do you change a cylinoid in a 1992 ford ranger?

Depending On which solenoid if it is a starter solenoid there is one on the inner fender and one on the starter the one on the inner fender is changed by disconnecting the battery then removing the wires making sure to know where they go when you put the new one on then unbolt it and bolt the new one in the same way in reverse if it is the one on the starter however your best bet is to replace the starter completely it is more ecconomical in the long term of your vehicle Depending On which solenoid if it is a starter solenoid there is one on the inner fender and one on the starter the one on the inner fender is changed by disconnecting the battery then removing the wires making sure to know where they go when you put the new one on then unbolt it and bolt the new one in the same way in reverse if it is the one on the starter however your best bet is to replace the starter completely it is more ecconomical in the long term of your vehicle


Where is the starter solenoid on a 1999 Dodge Dakota?

Right side of vehicle under the oil filter for 4.0 engines. It is located on the starter. The solenoid is another smaller cylindrical shaped device that is mounted to the starter. If you have to replace it you have to buy the whole starter assembly that comes with a solenoid. I have not found a way to replace only the solenoid. Jeep engineered this to benefit their dealer service garages.

Related questions

How do you change the starter in a 1997 GMC suburban?

disconnect + battery terminal take out 2 bolt out of starter from the engine block take off the wires remebering where they go do in reverse order to reconnect


How do the starter wires go on a 95 sunfire 2.2 engine?

How do the starter wires go on a 95 sunfire2.2 engine


How do you wire a starter for a Pontiac 400 engine?

where do the wires on the starter go on a 1977 pontiac 400


How do you remove a starter from a 02 impala?

I am currently having the same issue. First unhook the battery completely. Then you need to find where the wires on the starter are connected to the battery. Detach the wires from the starter that go to the battery. Once you have the starter wires completely detached from battery you can start removal of starter from engine block.


Where is the starter solenoid located on a 1997 Mazda mpv?

the solenoid is on the starter. It's the part the wires go into.


Where do wires go on 350 chevy mini starter?

The starter needs a large wire from the battery and a wire from the starter switch. These are connected to the solenoid that is attached to the starter.


Where is the starter located on a 1989 Ford Bronco and how do you replace it?

its located where the tranny bolts up to the motor. disconnect the three wires from the starter, then take the three bolts out of the starter and pull it out. just remember where the wires go!!


What is the shape of the Start Relay of 1995 Plymouth Acclaim Sedan Auto?

The Starter relay for Acclaims are located right on the starter, its what the wires that go to the starter hooks to.


How do you remove a starter from Hyundai sonata?

Look to the front left of the engine where the transmission mounts to it, you will see the starter there and it has several large wires bolted to it. Remove those wires ( after you have disconnected the battery ) and then remove the two bolts holding the starter on, replace with the new one and reconnect the wires, then reconnect the battery and off you go.


How do you replace the starter on a 2001 Chevrolet S10?

you disconnect neg. side of battrey and then raise the truck and some times over the th rt front over the tire you can get to the wires to disconnect if not go under car and look at starter should be able to acess the wires only 2 of them then take the 2 mounting bolts for starter, remove them and then sneak the starter out it will be alittle tight to do so take your time. there might be a shim between starter and engine if so must use it with new starter unless the new starter may say no shim needed, would be printed on the head of starter. if no shim install with no shim. when installing and you connecting wires be sure that wires are not! touching together if not sure when you go to connect battery it will spark badleyand starter will engauge at that point leave battery disconneted double check wires at starter.


How do you install a starter for a 1988 Chevy 305?

Un-Hook battery- Unhook wires off old starter. (should be 3 wires ) some are 4 If unable to access wires take starter off first and then take off wires, Unbolt starter- will slide forward towards front of vechicle- and replace new starter everything vise-versa-- Don't worry because their is No way to put it in wrong because it will only GO in (1) way.. Note: U may want to mark your wires- so that you know where to place them when you put the new starter in.


How to remove a starter on a 92 Chevy Suburban?

disconnect your battery, {neg. cable first} then pos. cable, go under your car/truck and unbolt starter. There you have it. To install work it backwards