0
Where do you hook up the 2 leads of a push button remote starter on a Ford 350 Econoline Van?
Wiki User
∙ 13y ago
belt
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you check for power to starter on polaris 400?
Remove the skid plate off the bottom of machine . Take a standard test light , hook the clip to a good ground and touch the probe to the post on the starter . Push the start button and the light should light . If the light works and lights but the starter doesnt work take a small hammer and tap the starter while holding the start button . If the starter workes then the brushes are shot on the starter and need replaced .If the light does not light on tester go to the battery and follow the leads to the starter solonoid . One side of the solonoid should light up without pushing start button , the other side will light up when the button is pushed.
How do you reverse starter rotation on a club car starter?
reverse solineoid leads
How do you test a cyllinoid?
Assuming for the sake of argument you meant "solenoid" and are specifically referring to the starter solenoid:You can purchase a remote switch, follow the package directions that show you where to attach the leads, and hit the button. (Optionally, if you are particularly brave and/or stupid, this can be accomplished with any standard screwdriver.) If this starts your vehicle, then your problem is elsewhere. If not, and you can determine the battery is not the problem, remove the starter with the solenoid and take it to any reputable auto parts store where they will be able to test the unit for you free of charge.
How do you locate the starter motor on rover 400?
Follow the thick red cable from the positive terminal on the battery. It leads straight to the starter motor.
What causes 2004 jeep to not crank eventhough it still has full battery?
start back at the battery, are the leads corroded? is there a clicking noise when the starter is engaged but the starter wont turn? are the leads from the battery to the starter in good condition. Usually any sign of a white powder around the battery or a lot of dirt is a sign of needing attention. The clicking could be a starter relay aor the starter itself needing replacement.
How difficult is it to replace a starter on a 2000 Silverado Z-71?
its not that bad to bolts starter comes out disconect your battery first after the starter is down you will be able to take the to leads off the starter pretty easy job drive safe
Where is the starter motor located on a reliant robin?
easy as cake to find any starter motor follow the largest positive red wire from the battery, for the most part it always leads to the starter.
Where is the starter on 98 Chevy blazer?
Lower, rear passenger side of engine. Best reached from under the vehicle. Positive battery cable leads right to the starter.
How to replace the starter in a 1986 Honda accord?
1. Disconnect the battery negative terminal 2. Disconnect the leads to the Starter Soleniod (the cylindrical thing on top of the starter) 3. Remove bolts attaching the starter to the engine 4. Remove Starter 5. Installation is the reverse of these instructions. Hope this helps...
What is the solenoid starter relay wire order for a '93 Ford Aerostar?
it is the wire that runs between your starter and your silenoid. your silenoid is generaly located on the inside fenderwall of our engine compartment. it is about 3" tall, 2" in diameter, and has 2 large leads coming out either side with 2 smaller leads coming out between those. there should also be a red and a black wire attached to the large leads. generaly the red one runs to your starter. this is the wire you are looking for.
What would cause a motorcycle not to start when you press the starter button?
First obvious problem woutl be a dead battery, but if battery turns over and still doesn't start the engine then the reasons multiply, could be disconnected plug leads, bad spark plugs, flooded carb. etc.
How do you check the starter solenoid relay on Kawasaki Vulcan 1500?
Short the two battery leads together, this will bypass the solenoid and should turn the starter. But this does not answer the question....it just lets you see if the starter works. How do you CHECK the solenoid to see if it is GOOD or BAD???
