0
Where is and what does it look like the inline spout connector on a 1995 ford F-150 4.9 liter motor?
Wiki User
∙ 13y ago
i have never heard of a spout connector. need more information
- Its a little square gray plug with 2 wires going into it usually taped to the wires that go to your ecm - hope that helps
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
What is a inline spout connector?
wer is the spout connector on 1992 ford e150 v8 5.0 liter
Where is the spout connector on 1990 ford f150 5.0 liter?
I believe it should be close to the distributor at the front of the engine
93 ford ecoline van e 350 put in a new ingition modular and a new distributor how do you set the timing when putting the timing light on it do you have to unplug anything first?
There is an inline spout connector, kind of like a plug you would plug into the wall, that you have to disconnect before using timing light. This puts the engine in base timing. Set timing to specs and then plug inline spout connector back up.
Where is the SPOUT connector on 1997 ford ranger 4.0L V6?
I'm not a mechanic / technician but I believe the spout connector is by your COIL PACK
Where is the spout connector on 95 ford 7.5 liter motor for timing procedure It says you cant reset timing but it gives a timing to be set to Can you time this ignition?
I have a RV built on a 1994 E-350 Ford chassis with the 7.5 liter engine. I finally found the SPark OUTput (SPOUT) connector behind the driver side battery. It is a gray plug in a black socket. It was taped to the wiring harness that goes to the ignition control module (ICM) which is also behind the battery. The tape completely covered both the plug and socket making it very hard to find.
Where is the spout connector on 1992 ford f-150?
where is the spout control on a 1992 ford f150 300 6 cyl
Where is the spout connector on a 1997 ford contour 2.0?
um just no
I have an 1989 Ford - 302 needing help with ignition timing I've tried between 5 BTDC and 10 ATDC with no difference What's to be considered as TDC will allow the truck to respond in park not in gear?
I'm not a mechanic / technician but I remember having to disconnect the " spout connector " which is a little jumper wire plug near the distributor to set the static engine timing on a 1991 302 . I checked my repair manual and your timing should be 10 degrees BTDC The spout connector disables your computer control over the ignition timing. This MUST be removed for proper timing. If you have properly unplugged the spout connector you will notice NO change in timing when you rev the motor. If the timing fluctuates while reving you unplugged something else. It is usually a Square plug inline from the distributor on the yellow wire. On newer models it is a round plug. When you plug your spout connector back in your timing will no longer be 10 BTDC because the computer now has control over the ignition timing. And btw, if you go 10ATDC you will have zero power, if it even stays on at all. And if your setting to ATDC with the spout connector in the computer is compensating for the outrageous timing setting.
Where is the spout connector in a 1989 thunderbird 3.8 cu-in?
Behind Passenger Headlamp.Weatherall'sAutomotive
How do you adjust the idle on a 1994 Ford Mustang without a distributor?
The screw on the side throttle body If its not a PCM with electronic engine idle control. Most of today veichles you can not adjust idle. What motor do you have cummins? Like can people be a little more specific?? Pull the Spout Connector Before changing Idle Screw and make sure its up to operating temp then turn the idle screw on the Throttlebody.Replace the Spout Connector then all should be well,If you disconnect the Battery for any length of time you must remove the Spout Connector again to allow it to Relearn the Position.
Where is the spout connector on Ford 460?
I have a RV built on a 1994 E-350 Ford chassis with the 7.5 liter engine. I finally found the SPark OUTput (SPOUT) connector behind the driver side battery. It is a gray plug in a black socket. It was taped to the wiring harness that goes to the ignition control module (ICM) which is also behind the battery. The tape completely covered both the plug and socket making it very hard to find.
How do you set the timing on a 1991 Cougar V6 3.8?
if its dis you can't but if not you have to unplug the spout connector
