Auto Parts and Repairs
Chevy Silverado
Crankshaft Sensors
Chevy Trailblazer

Where is the O2 sensor and crank sensor located on a 91 Chevy Lumina 31L and is it fairly simple to replace yourself?

232425

Top Answer
User Avatar
Wiki User
2006-10-22 23:41:03
2006-10-22 23:41:03

I have a 92 lumina with a 3.1 and I found the crank sensor to be located on the passenger side of the engine in the back of the engine NOT on the side of the engine below the knock sensor. Hello, in my experience, all O2 sensors are located in the exhaust just after the manifold. It appears easy enough to change. If it is the crank position sensor you are looking for, take a look around the main pulley at the bottom of the engine, you may see a square-ish component located close to the actual pulley wheel, this would be the crank position sensor, it should have wires connected to it.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Your vehicle speed sensor. I Believe it is located near your transmission under the car. fairly easy to replace

User Avatar

It is located in the oil pan. Fairly big job to replace.

User Avatar

`150-200 (rotor about 80.00-approx.) You can do it yourself if you are fairly handy.

User Avatar

you should be able to take the cover off the driver's door by unscrewing it,then unplug the window switch and replace it,fairly easy..

User Avatar

The water pump is located in the middle of the front of the engine. The water pump is fairly easy to reach and replace.

User Avatar

the fuel pump is located in the fuel tank witch is located under the car in front of the rear axel. fairly easy to replace. if u can take it apart u can put it back together

User Avatar

i have a 89 Chevy lumina but im fairly certaint ur fus is going to be located in same place wich there is a fuse box under the hood there it should have 3 or 4 big block size fuses mine was one of them it should tell you on the fuse pannel its self

User Avatar

Knock sensors can be a pain to get to (located under the intake manifold) combined with being fairly cheap, it would be better just to put a new one on by the time you get to it. If you have a code indicating the knock sensor is bad just replace it and save yourself a headache.

User Avatar

The blower motor resistor is located under the front dash on the passenger side of the truck. It is a fairly simple job to replace...maybe 15 minutes. The blower motor resistor is located under the front dash on the passenger side of the truck. It is a fairly simple job to replace...maybe 15 minutes.

User Avatar

Just had my turn signal switch replaced, for the second time, on my '98 Chevy Lumina. I paid $260 to a fairly trustworthy auto repair mechanic

User Avatar

It is fairly simple, easier on a manual transmission. If you search for subaru forums, a lot of them have do it yourself write ups, with pictures even!

User Avatar

Replacing a bathroom sink is fairly easy and definitely worth it for you to do for yourself. You can find instructions on how to replace it here: http://www.ehow.com/how_2099972_replace-bathroom-sink.html

User Avatar

It is located in the front of the engine towards the top. If you follow the radiator hose it will lead you to the thermostat. There are two bolts that hold it in place. You can remove the bolts fairly easily and replace the thermostat. It is important that you make sure that everything is clean when you reassemble everything.

User Avatar

I have a 1990 Lumina Euro 3.1 that done this and it about drove me crazy. I had replaced all 3 coil packs and thought it fixed it but then it happened again. Come to find out it was the ECM that sits directly under the coil packs. It's fairly easy to replace but the starter wire is in the way of the center coil pack, so you may have to remove it. Hope this helps.

User Avatar

possibly low on freeon. ** Fairly cheap fix from the local auto parts store.

User Avatar

Yes. And consider yourself lucky, if you do.

User Avatar

It's fairly difficult as you need to replace a seal thing and turn the water off.

User Avatar

It is located on the passenger side of the car, bottom of the engine. (just inside of the Right front tire) there are two bolts that hold it on plus the wiring. It can be dropped out in about 5 or 10 minutes and is fairly easy to replace.

User Avatar

The temp blend door actuator is located on the HVAC unit behind the dash assembly. To replace the temp blend door actuator the dash assembly needs to be removed. This is a fairly large job with to many steps to post here. If you intend on doing it yourself I would recommend purchasing a shop manual for that vehicle. The manual will pay for itself after the first job.

User Avatar

Knock sensors are located under the intake, which is dry with a low torque gasket. Fairly easy if you deem yourself somewhat of a mechanic. Costly at the shop. Buy a manual if you are to attempt yourself along with the tooling.

User Avatar

Just be yourself! And if they like you, it will be fairly obvious.

User Avatar

Watch tutorial videos a few times before trying to accomplish the task yourself. This way one won't permanently destroy their motherboard forever, given that they are fairly costly to replace.

User Avatar

It is fairly easy to shampoo your own carpets. I would save the money and do it yourself.

User Avatar

Yup, These handles Break on these cars. Its fairly easy to replace. I did it by myself. Take off the original Door handle assembly and take note exactly how you took it apart, then put the replacement on. Doesn't take that long either. Shouldn't be hard to mess up.

User Avatar

the battery is in the trunk , it should be fairly simple


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.