Ford Probe
Ford Explorer Eddie Bauer
Ford Explorer XLT
Ford F-150

Where is the back up light switch for 91 Probe LX 3L with automatic transmission located?

101112

Top Answer
User Avatar
Wiki User
2008-10-11 06:20:11
2008-10-11 06:20:11

behind brake pedal

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

If its a manual transmission: There isn't one you have to pull the plug on the transmission itself.If its a automatic transmission: Its located near the firewall on the passengers side of the engine compartment.Hope this helps!

User Avatar

what type transmission fluid uses for a 1991 ford probe

User Avatar

all you have to do is take the pan cover off. which is located just behind the raditor on the driver side. you do not have to take out the transmission to do so.

User Avatar

If The Probe Is an automatic then your car has CD4E Tranny in it. The pan for these trannys are on the front side of the transmission. They are not underneath it. Hope this helps.

User Avatar

Yes. Be sure to change the neutral switch from your probe as the mazda's will plug in but is wired different.

User Avatar

You check it and add fluid at the same place. Look on the transmission for a dipstick.

User Avatar

on an automatic trans through dipstick tube

User Avatar

between the engine and the drive wheels

User Avatar

CHANGE TRANSMISSION AND PEDALS CHANGE ALLL THE AUTOMATIC STUFF TO FIVE SPEED STUFF No you cannot put a 89 transmission in a 95. There were 2.2 in the earlier years the 89 transmissions will only fit from like an 89-92. Then from 93-97. Which have a 2.0.

User Avatar

Manual =2.9 quarts. Automatic =9.3 quarts

User Avatar

assuming they are the same engine/transmission configuration (ie: 4cyl automatic or 6cpy standard or 4cyl standard or 6 cyl automatic) they are the same and should be interchangeable

User Avatar

The quantity of transmission oil is 9.6 liters. It is important that Mercon oil is used, not Dexron or any other type.

User Avatar

its possible to do anythign, as long as you wanna put the work into it.. if its the same motor its easier...make sure you do all the pedals, and you will have to swap the computer too

User Avatar

The switch is just across from the battery located in the rad reservor, to remove it and clean the sensor probe, you have to remove the battery.

User Avatar

no it is not , your looking approx. 8.5 hrs in and out to replace a probe transmission....

User Avatar

If you're talking about the VSS, it's located at the top of the transmission, above the transmission output shaft. It looks like a probe, but you're only going to see the top of it until you remove it.

User Avatar

The 1991 Ford Probe does not have a transmission fluid intake reservoir. All of the transmission fluid is contained in the transmission.

User Avatar

The fuel cutoff / inertia switch is located in the trunk on the left side quarter panel under the carpet. Most have a rubber boot on them.

User Avatar

sounds like you need to replace the neutral safety switch. ignore the next answer i had the same problem with my 89 ford probe i just out it in park revd it up and it would go away but sometimes i had to hit the transmission with a hammer

User Avatar

It is important to check and maintain the fluid levels while owning a car. The transmission dipstick of a 1993 Ford Probe is located behind the engine, to close to the firewall and it has a yellow cap.

User Avatar

how to check the fluid on a manual transmission for a 1989 ford probe gt

User Avatar

Under the air cleaner box, on the right side of the transaxle.

User Avatar

if automatic first install a extra transmission cooler,and use syntheic ATF.You can turbocharge engine to make it faster.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.