answersLogoWhite
Dodge Caravan
Pontiac Bonneville
Chevy Blazer S-10
Ford Explorer XLT

Where is the cam sensor located on a 1994 Bonneville?

151617

Top Answer
User Avatar
Wiki User
2005-12-14 22:54:02
2005-12-14 22:54:02

The cam sensor is located on the pass side of the motor below the power steering pump and to the right it has a 10mm bolt holding it in place and a 3 wire plug I dont think you can see it but you can feel it and takes about 10 mins to change and cost is about $25 new good luck.

1

Related Questions

User Avatar

The cam shaft sensor is located behind the water pump pulley. One bolt that holds it in place.

User Avatar

The 1994 Oldsmobile Cutlass cam sensor is located on the back of the left cylinder head. The cam sensor should be labeled as such.

User Avatar

on a 93 Pontiac Bonneville you would remove the passenger side front tire. there may be a plastic cover that just pulls off. look to your left,back and up a little bit you should see the wires that connect to your cam sensor. theres your cam sensor. 91 Bonneville is probably the same.

User Avatar

The cam sensor should be located underneathe your distributor cap. That is the placement on my 98 Grand Cherokee and it should be located there as well on yours.

User Avatar

THE CAM POSITION SENSOR IS PART OF THE DISTRIBUTER, AND CANNOT BE SERVICED

User Avatar

The cam sensor on a 1987 Bonneville is just below the water pump, it has a gray electrical connector.

User Avatar

That year did not have a cam sensor.

User Avatar

where is cam senor on a 91 cutlass ciera 3300

User Avatar

On a 94 Turbo DSM there is no crank angle sensor. The Cam Angle Sensor(CAS)serves the function of both a crank and cam sensor, and it's located on the passenger side of the valve cover at the end of the intake camshaft, you can't miss it.

User Avatar

The cam sensor is located on the left side of the engine (as your looking at it) on the valve cover

User Avatar

The cam sensor on a 2003 Kia Rio is located on the front, driver's side of the engine. It is found next to the crankshaft sensor.

User Avatar

The cam sensor is located on the left side of the engine (as your looking at it) on the valve cover. It is the only sensor that is located on that side on the upper part of the engine.

User Avatar

IS CALL CAMSHAFT SENSOR AND IS LOCATED ON THE RIGTH SIDE OF THE ENGINE , ABOVE THE CRANK PULLEY You will have a crank sensor, but it won't have a cam sensor. it dose have a cam sensor, on the timing cover left sind of water pump

User Avatar

The Cam sensor is located at the right rear corner of the cylinder head

User Avatar

1992 Chevy trucks did not have a CAM SENSOR. They had a distributor.

User Avatar

Cam position is taken from the distributor. There is no separate cam sensor.

User Avatar

There is no cam sensor on the 1995 year engine. GM. did not use a cam sensor on that year.

User Avatar

84 does not use a cam sensor. it does however use acrankshaft position sensor located in the lower front section of the engine assembly.

User Avatar

a 1993 doesn't have a cam sensor. the crankshaft position sensor is located on the front of the engine directly above the crankshaft pulley

User Avatar

Assuming that it is a 3.1 V6, as most of them are, there is no cam sensor. Only a crankshaft sensor. It is located behind the harmonic balancer. To replace it the balancer has to be removed.

User Avatar

Cam position is taken from the distributor on this vehicle, there is no separate cam sensor.

User Avatar

Installation throttle positionsensor


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.