it is below the valve cover.Take off the valve cover and it should be the cam shaft closer to you.If you are trying to retime engine you will need a special bar like tool to time it.This bar fits in the grooves at the end of the two camshafts on the drivers side.
The crankshaft position sensor, on your 1992 Buick regal 3.1 liter, is located on the back of the engine. The crankshaft position sensor is on the inside of the engine cover.
The crankshaft position sensor in a 2002 Jeep Grand Cherokee 4.7 liter is located left of the starter. In order to remove the crankshaft position sensor the CKP mounting bolt will have to be removed first.
Where is crankshaft position sensor located on a 1996 Toyota corolla 1.6 liter?Read more: Where_is_crankshaft_position_sensor_located_on_a_1995_Toyota_corolla_1.6_liter#ixzz1nWxVCKMW
The crankshaft position sensor on a 1998 3.0 dodge caravan is located on the top of the bellhousing towards the firewall.
The 1999 Chevy Lumina 3.1 liter engine crankshaft position sensor is located on the back of the crankshaft. A diagram can be obtained from most Chevrolet dealerships.
Where is located
The crankshaft sensor on a 2005 Dodge Stratus 2. 4 Liter is located on the bottom of the engine, near the oil filter. It constantly monitors the rotation of the crankshaft and updates the vehicle's computer on its current state.
It is located back by the belhouseing on the left side.
where is the crankshaft position sensor on 2.5 liter vw jetta
CID = cylinder identification sensor is the same as a Crankshaft Position Sensor. Look for it by the harmonic balancer
if it is a 2.4 "x" motor, the crankshaft position sensor should be located in the front of the motor "TUCKED" up behind the starter. it is very difficult to find, but it s there.
The crankshaft position sensor is located on the rear of the engine. It is mounted just above the oil pan on the engine block.
The crank sensor will be located iether behind the harmonic balancer or right on the side of the engine block
The crankshaft position sensor is located on the front of the transmission case next to the fly wheel on Kia's from 2000 to 2005. On Kia's built after 2005 it is located next to the outlet assembly and the radiator hose inlet.
The Crankshaft Position (CKP) sensor is located at the right-rear side of the engine cylinder block CKP Sensor Location/Removal/Installation - 4.7L V - 8 Engine It is positioned and bolted into a machined hole in the engine block
Near the bottom timing belt cover (on the top left).
It's located behind the crankshaft pulley bolted to the engine block.
try to replace the camshaft position sensor located under the power steering resivoir .. on 4.6 liter lincoln ...
crank sensor is located at the top of the transmission bell housing,two hex bolts that hold the crank sensor in place.
The HyundaiÊ1.3 liter engine crankshaft position sensor can be found on the back of the engine. You will need to remove the rear engine cover in order to access the crankshaft position sensor.
it is located on the top of the bell houseing at the back of the block
The crank position sensor is located by the crank shaft on a ford 350 xl 5.8 liter.
It is above/behind the starter. The starter must be removed in order to access the sensor to change it.
I'm not a mechanic / technician but on a 1998 Ford Ranger 4.0 liter EFI , V6 engine : I believe the crankshaft position sensor is at the front of the engine When standing in front of the vehicle looking into the engine compartment it is just to the left of the crankshaft damper near the bottom of the engine
Some place in the world i think