Its located behind the glove compartment, a rectangular black box a little bigger than a pack of cigarettes.
The remote has a radio transmitter built in. The car has a receiver connected to the car locks. The signal from the remote turns on certain circuits in the receiver causing the doors to lock or unlock.
it doesn't have one. The one for the trunk is in the glove box, dan94z
Most remotes from 90 on require you to hold down both unlock and lock buttons for 7 seconds to reset remote after changing the battery.
It doesn't have one, it opens when you unlock the car doors with your remote.
One reason that your remote key will not unlock your Mazda 6 is that a fuse is blown. You may need to replace the batteries in the remote or reprogram the remote. A bad body control module is another reason the remote will not unlock the doors.
1. Turn your key to the "Run" position, but do not start the engine. Shut the doors and wait for the warning beeps to stop. 2. Hold the "Unlock" button on the currently programmed remote for five seconds, and then press and hold the "Panic" button (while still holding "Unlock") for one second. 3. Press and hold the "Lock" and "Unlock" button on the same remote for a few seconds, then release the buttons and press the "Unlock" button. 4. Press and hold the "Lock" and "Unlock" button on the new remote, then release the buttons and press the "Unlock" button. Repeat the procedure for up to four remotes within 30 seconds.
To program a remote you must already have a working remote. If you do not have a working remote you must take to the item to a dealership or automotive locksmith for programming or ground a certain wire. (Google that) Procedure 1 1. Insert key into the ignition turn it to the ON position ( do not start the car) 2. Press and Hold Unlock on the functioning remote for 10 seconds. 3. While holding the Unlock button press the Panic button for one second. Release both buttons at the same time. Vehicle will chime signaling programming mode. 4. Press any button on the 1st remote to reprogram vehicle will chime again. 5. Press any button on additional remote to program a second remote. 6. Turn off ignition to exit programming. Procedure 2 1. Insert key into the ignition turn it to the ON position ( do not start the car) 2. Press and Hold Unlock on the functioning remote for 10 seconds. 3. While holding the Unlock button press the Panic button for one second. Release both buttons at the same time. Vehicle will chime signaling programming mode. 4. Press the lock and unlock button together on the remote and release. Vehicle will chime press and release the Unlock button and the vehicle will chime again signaling programming. 5. Press and release Lock and Unlock together on the second remote vehicle will chime. Press and release Unlock button on the remote vehicle will chime again signaling successful programming. 6. Turn off ignition to exit programming.
To unlock your Mediacom receiver, you will need to contact Mediacom customer service and provide them with your account information and the reason for unlocking the receiver. They will then guide you through the process of unlocking your device.
Unlock the car with the remote or the key in the door.Unlock the car with the remote or the key in the door.
Unlock the car with the remote or with the key in the door.Unlock the car with the remote or with the key in the door.
How do you program a keyless entry remote for a 2002 dodge1. Press LOCK button 5 times at 2 second intervals to resynchronize remote.2. Insert key into the ignition switch. Turn ignition to the RUN position (as far as you can go without cranking engine). Wait for ignition chimes to stop.3. Using the working remote, press and hold the UNLOCK button on the remote for 4 to 10 seconds.4. Within the specified 4 to 10 seconds, continue pressing the UNLOCK button and then press the PANIC button ( on the programmed remote ) for 1 second and release both buttons. A chime will sound to indicate that the remote programming mode has been entered ( allow 3 seconds for chime to sound ).5. Within 30 seconds of the chime, press and release the LOCK and UNLOCK buttons simultaneously then press and release just the UNLOCK button on the same remote. A chime will sound indicating the remote has been programmed. Press and release the LOCK and UNLOCK buttons simultaneously and then press the UNLOCK button on each new remote you wish to program at this time. Locks will cylce afer each additional remote is programmed.6. Turn the ignition OFF and remove key.7. Test Remotes.
have you checked to batteries in the remote?