Car Electronics and Lights
Ford Ranger
Dodge Ram
Turn Signals and Hazard Lights

Where is the turn signal hazard flasher located on a 1997 Ford Ranger pick-up truck?

737475

Top Answer
User Avatar
Wiki User
2004-12-25 21:06:35
2004-12-25 21:06:35

I have a '98 model. The flasher unit on it is located under the steering column. You'll have to remove the hood release bracket then the plastic panel. There's another metal panel behind this. Remove that too. The flasher unit on mine is bright yellow with six wires. There are torx head screws securing the plastic panel as I recall.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The 2004 Ford Ranger pickup truck signal hazard flasher unit can be found beneath the drivers side dashboard. The signal hazard flasher unit will be above the brake pedal.

User Avatar

how do you replace a turn signal flasher on a 1999 ford ranger pickup

User Avatar

the turn signal flasher and the hazard flasher are located in a small canister shaped unit located in the wiring harness under the dash near the steering column. in all Isuzu trucks from 81'-93'

User Avatar

There is no flasher can. There is a relay at the lower left in the fuse panel on the side of the dash. There is one relay that serves both hazard and turn.

User Avatar

Front seating area, behind steering column cover, on left hand side of steering column. I bought a replacement flasher at pepboys(part # EP27) It din't work in my ranger. So I bought another at the Ford dealer and this works. The flasher looks like a relay( http://www.partsamerica.com/ProductDetail.aspx?mfrcode=TRD&mfrpartnumber=EP27 ).the OEM flasher usually is blue.

User Avatar

on a 1989 Isuzu pickup you need to take out the left speakerto get to the signal and hazard light flasher ..The control box for the flashers and turn indicators is all contained within the steering column. Not the easiest to get to.

User Avatar

The 1986 Toyota pickup flasher relay switch is located beneath the dashboard on the drivers side of the passenger compartment. The flasher relay switch will be labeled as such.

User Avatar

The combination flasher unit is located behind the upper lefthand side of instrument panel.

User Avatar

The 1973 Ford F2 50 pickup truck turn signal flasher unit is located behind the drivers side dashboard. The turn signal flasher unit will be near the back of the speedometer.

User Avatar

There are 2 flasher relays. One for the turn signals and one for the hazard lights. The Turn Signal flasher is located on the drivers side, passenger side of steering column, under dash mounted near cigarette lighter. Optionally it can be mounted under the dash on the drivers side of the steering column. The Hazard flasher relay is mounted in the exact same locations.

User Avatar

hazards and turn signals have separate flashers. replace flasher for turn signals

User Avatar

Flasher Relay is located Front seating area, driver side, under dash, driver side of steering column, mounted in relay bracket.

User Avatar

The 1989 Ford Ranger pickup truck ignition module is located on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall.

User Avatar

The turn signal flasher on a 1995 Dodge Pickup is located on the driver's side under the dash. It is right next to the fuse box above the brake pedal.

User Avatar

The Chevrolet K1500 pickup truck flasher relay switch can be found beneath the drivers side dashboard. The flasher relay switch will be above the brake pedal.

User Avatar

Under dash, driver's side. The flasher may be located someplace else under the dash.

User Avatar

The blower resistor assembly is located on the heater case to the right of the bloser motor. - Haynes Repair Manual #36071, 1993-2005 Ford Ranger Pick-ups

User Avatar

I have a 1990 Nissan Pickup 4 cyl. manual transmission. The Flasher is under the dash to the left of the steering wheel. It is near the top of the clutch petal. Turn the key on and start the signal. You should hear where it is at. Put your hand on it and you will feel the vibration and the sound will change. I still have not figured out how to get it off.

User Avatar

There is one flasher that works both the hazard lights and blinkers. It is a 5x5ish silver box mounted to the firewall behind the radio. It has a two- prong connector on the face. If your hazard lights work and the blinkers don't or vice-versa, your problem is not the flasher. The hazard light switch does all of the routing of electricity to the lights based on its position and that of the blinker lever. The switch is purely mechanical and often gets oxidation on the contacts. Remove the switch, open it (careful for the springs and floating contacts inside), clean the contacts with emery cloth, reassemble, and reinstall. With luck, this will take care of your problem. If the flasher itself is your problem, you may have to go to Toyota for it. The ones that AutoZone and other parts stores sell are three prong, so they won't work.

User Avatar

The average trade in value for a 2001 Ford Ranger pickup is around $1,500 for the average, "no frills" model.

User Avatar

where is the VIN located on a 1937 ford pickup

User Avatar

it's a big (compared to fuses and relays) metal grey round thing that's in there with the fusebox


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.