answersLogoWhite

0


Want this question answered?

Be notified when an answer is posted

Add your answer:

Earn +20 pts
Q: Why does your 2002 ford excursion rear blinker not work when the fuse and bulb are fine?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Why don't your blinker work when your flashers are fine?

I found that it was a burnt out bulb


1993 Mercedes 190E the left blinker on the panel in dash does not light up but does work outside but the right blinker works fine what to do?

Sounds like the light bulb is either loose or burned out in the dash. Replace it.


What do i do if my right turn signal doesn't blink when i turn it on it's a 2000 camaro the dash light and the blinker just stay lit?

a bad blinker bulb. replace the bad one and it'll blink fine.


97 Pontiac Sunfire with a rear right blinker problem I have replaced the bulb. The brake lights work tail lights work hazards work but the right blinker isn't working. Checked fuse also fine?

try replacing the flasher. there should be two, one for flashers and one for turn signals


Why would your right blinker quit working while the left one works just fine on my '97 Dakota?

It sounds like it is either as simple as the bulb being blown or the possibility of the switch being broken.


Why does my blinker work fine then blink fast then work fine again?

The signal flasher relay may be on its way out.


How do you repair blinker system on Malibu Chevy 2002?

The 2002 Malibu had a factory recall for a defective turn signal relay. Replace and it should work fine. If you can find paper work from GM about the recall, a GM dealership should do it without charge.


2001 Trans am- left blinker stayed on right one worked fine Replaced the left bulb and the fuse because it was blown blinkers worked fine for a few minutes then the fuse blew again What could it be?

You have a dead short to ground. It will take some detective work to inspect the wiring and sockets until you find it. The problem seems to have started with replacing the left bulb. Start there.


On a 1999 Olds Intrigue what's the fix for hazard lights and one blinker to work fine but other blinks twice as fast and front light doesn't flash at all?

Check to see if the bulb that does not flash is going bad, or is burnt out.


How do you replace left rear turn signal bulb on a 2002 sport trac?

Open the tail gate and find the 3 rubber plugs on the left wall by the lamp. Pry them out with a flat screwdriver. This will allow you to loosen the 3 screws that hold the tail lamp in. Unscrew the bottom bulb. If you find out the bulb is fine, you might check that the wires in your steering column to the blinker switch are tight. There has been alot of these with wires coming loose, as is in my case with my '01. Try adjusting the tilt steering up and check the function of the signals. Good luck.


Your right turn indicator blinks too fast but only when the lights are on Left turn is fine all bulbs are fine and it works correctly when the headlights are off Any advice?

I had a fast blink on the right turn signal of 96 Grand Cherokee. Initially, this indicates a bulb out. Sure enough, it was the passenger front bulb (not the one on the side). Took it in and had repair shop replace bulb since I was having other work done. Now the signal works fine, except when I turned on the parking lights (or headlights), the blink goes fast. Took it back in to repair shop, they replaced all three other front blinker bulbs. Still not fixed. Looked up on internet, seems a common problem is using an 1156 instead of 1295na for the front blinker. Opened it up, found the 1156. Went to Napa auto parts, guy said it was an unusual bulb but he had one in the back. Popped it in, works as it should. .


Your brake lights don't work on Renault megane scenic fuse fine bulb fine brake light switch fine?

Its a common manufacturing fault. if you remove the rear light complete. then remove the actual bulb holder. If you then take out the bulb that seems not to be working, you will find that, there usually is some corrosion on the plate that contacts with the bulb. which stops current from reaching the siad bulb.