0
What else can I help you with?
How do you replace a tensioner pulley on a 2000 Oldsmobile intrigue?
To replace the tensioner pulley on a 2000 Oldsmobile Intrigue, first, disconnect the negative battery terminal for safety. Then, use a wrench or socket to relieve tension on the serpentine belt by turning the tensioner pulley counterclockwise. Remove the old tensioner pulley by unbolting it and then install the new pulley in its place, securing it with bolts. Finally, reattach the serpentine belt, ensuring it's properly aligned, and reconnect the battery terminal.
How to Replace belt tensioner on 2000 Chevy cavalier?
Remove serpentine belt. Remove alternator. The bolts that hold the tensioner on are under the alternator.
Where is the tensioner pulley to tighten the serpentine belt on a 2000 Chevy Silverado?
If you're standing at the front of the truck and looking into the engine compartment the tension pulley is on the left side about half way down.
How do you replace serpentine belt on a 2000 Chevy cavalier 2.2 liter?
Note:The drivebelt routing decal on the radiator shroud to help during drivebelt install * To replace the belt rotate the tensioner pulley clockwise to release belt tension * Remove the belt from the auxiliary components and slowly release the tensioner * Route the new belt over the various pulleys again rotating the tensioner to allow the belt to be installed then release the belt tensioner
Where is the tension pulley located on 2000 Blazer LS?
Look on the passenger front side of the engine, you will see pulley attached to a short arm with a square hole. That is the tensioner and tensioner pulley
How do you change serpentine belt on a 2000 Chevy cavalier?
Note:The drivebelt routing decal on the radiator shroud to help during drivebelt install * To replace the belt rotate the tensioner pulley clockwise to release belt tension * Remove the belt from the auxiliary components and slowly release the tensioner * Route the new belt over the various pulleys again rotating the tensioner to allow the belt to be installed then release the belt tensioner
How do you change a 2000 Chevy cavalier serpentine belt?
Note:The drivebelt routing decal on the radiator shroud to help during drivebelt install * To replace the belt rotate the tensioner pulley clockwise to release belt tension * Remove the belt from the auxiliary components and slowly release the tensioner * Route the new belt over the various pulleys again rotating the tensioner to allow the belt to be installed then release the belt tensioner
How do you release the belt on 2000 model gu patrol to remove alternator?
Loosen the tensioner pulley. The tensioner pulley will slide to the right. This will loosen the alternator belt. So it can be removed.
How do you replace tensioner pulley on 2000 dodge grand caravan with 3.0 engine?
You unbolt the old one (one bolt) then fit new. Now refit the belt.
How do you stop squeaking serpentine belt 2000 dodge Dakota?
98% of the time it is the tensioner or idler pulley. With engine off take WD 40 with that little plastic tube & spray the back side of either one, idler or tensioner pulley, not both. Take a drive & if you still hear the belt noise then it is the pulley you didn't spray. The tensioer pulley is replacable on most dakotas. When you remove the belt the tensioner should have strong spring action & move smoothly. If it does then just replace the pulley. Some places will try to sell you the whole tensioner.
Routing of a serpentine belt on a 2000 leganza?
I just did one today for my uncles 2000 Leganza 2.2. The trick is that the belt goes around the tensioner then the crankshaft pulley. It should make an s from the bottom of the alt. pulley to the tensioner then to the crank.
Can you take the tensioner pulley off without taking the tensioner off with it on a Dodge Grand Caravan 2000?
Yes, on a 3.3 or 3.8 the serpentine belt pulley does come off the tensioner arm but the bolt is left thread not right handed.
