If the damage is minimal then try and remove the door panel so you can access the internal workings of the door and try to get the catch mechanism to release that way. Hope This Helps.
Pulled from: http://answers.Yahoo.com/question/index?qid=20071001131029AAvU8LI&show=7
Don't hit it or kick it or push it or pull it...this is an easy one! When you pull up on your handle, these two arms on the handle in turn push two levers, one lever will pull on the right side rod and the other lever will pull on the left rod. After time these levers start to get bent out of shape from use. Eventually, when you pull up on your handle to open your tailgate usually one of the levers is so bent that is doesn't fully pull the rod enough to release the latch. One side might release but not the other. So here's what you do---lift up on the handle about halfways and look up under there. You can see where the two rods (the ends are in an 'L' shape) are inserted into plastic nuts. You can now see when you lift up the handle all the way which rod isn't getting pulled on---the one with the least movement. Those plastic rod clips clip onto the shaft of the rod after the tip of the rod is inserted into it. Let's first release the clips---Get a long flat-bladed screwdriver and position it under the part of the clip that is on the shaft. Pry up on it until it releases from the shaft. You can now push the 'L' shaped part of the rod out of the clip. Do that to the other clip also, although you might have to pry down on the clip to release it then remove the 'L' shaped end from the clip. Now you can manually pull the 'L' shaped ends of the rods towards each other to release the latches. Maybe a pair of pliers or needle-nosed pliers would be easier. Pushing on the tailgate to relieve the pressure on the latches may make it easier to pull on the rods too. You can also release one side at a time to open it. Once opened you can take the bent handle off of the tailgate and try to reposition the bent parts (which works a lot of the times) or just replace it. Just remove the three bolts on the inside of the tailgate and wiggle the handle out. Maybe hold the handle in the open position while removing it might help. Then you can operate the handle and see where everything makes contact with each other and see if you can put things back in the position they were supposed to be. When all is said and done be sure to WD-40 everything!!! Hope this helps
best of luck.
Obviously Yes, spare tire can prove to be a life saver...imagine in a time of emergency your car gets punctured at that time your spare tire would save you!!!
Focus on spelling their correctly.
Usually in the trunk in the spare wheel well.
This is where you insert a tool to lower the spare tire.
They went fishing and caught some sheep to cook for their meal!
The spare tire is located under the vehicle near the rear bumper
Did you ever get yours open?? I'm having the same problem.
In the compartment at floor level, driver side, beside tailgate.
If you mean Chrysler Town and Country, it's under the rear floor near tailgate.
almost all of the cj5`s had no tailgates and had permanant spare tire mounts. if you do have one either it was special ordered or someone did it later. that`s the difference with the 5 &7.the 7 was a little longer and had the tailgate with the swingaway spare tire mount. Actually the "FIXED BACK PANEL/RR SP WHL MOUNT" was a $12 option in 1978. I have the factory window sticker for a 1978 CJ-5 listing it. The 1978 Jeep sales brochure lists it under "Options and Accessories" as "fixed back panel and spare mount (CJ-5)".
The long scissor jack crank supplied with the vehicle is the tool for lowering the spare. Insert it into the hole in the back of the truck below the tailgate and locate it into the hoist socket. I think it's anticlockwise to lower.
The cast of The Spare Room - 1932 includes: Charles Courtneidge as Jones Roland Gillett as Hiram Harris Jimmy James as Jimmy Kathleen Joyce as Rita Charles Paton as Mr. Webster
It's either inside in the rear compartment, hanging off the tailgate or mounted directly underneath in front of the rear bumper.
the canister vent valve is located behind the spare tire you will have to take the spare tire so you can see it
You need to first swing the spare tire out of the way, roll the window all the way down then just lift the handle that is on the inside.
The word 'tightly' is an adverb, a word that modifies a verb or an adjective. Example sentence: The spare tire was tightly jammed in the well and it was difficult to get out.
One of the most likely causes is the tailgate was bent by the spare tire hitting something when backing or even going forward when the rear of the vehicle encounters an obstacle that exceeds the angle of departure, like dropping off a step or ledge. You should be able to see this. You may be able to reverse the damage by simply bending the tailgate back to where it should be.