email meet and I will send you a PDF showing and explaining exactly how. vbdenny.com I needed a direct anwswer so this is it now that I just finished replacing my 1993 LS400 brake light. 1. open trunk 2. gently pull back the carpet - like covering where the light is located and it will pull off and fold it back by weighting it down or having a friend hold it 3. look for two bolt head to the rear side which could attach the rear light and two other nuts that are all the same size which appear to be attachments to the rear light back portion (one may be hidden under a popped out piece of metal) 4. after removing these 2 nuts and bolts grab the screw sticking out at the top and pop out the top one by pushing back and the plastic surround over the rear light on the top of it should pull off gently and straight back 5. this opens up the light so you can gently wedge the top of the light with a flat head screw driver toward you and it will cause it to pop out so you can lift the entire rear light out 6. turn the bulb holders counter clockwise about a 1/4 turn to pull the bulb out 7. replace bulb by pushing down gently and turning it out 8. install new bulbs - do all three of the them just because this job is not worth doing again unless absolutely necessary 9. reverse your steps and if you don't have the snaps chew some bubble gum to hold it in place temporarily (just a joke but I might do it rather than going to buy a broken snap at the Lexus dealer) Say a prayer for those who follow in your path to unlock the secrets of how Lexus can make a good product and still force the average person to spend money just changing a light bulb - but then you aren't average if you accomplished this ... you're so thrifty and determined to crack the secret codes of the Lexus laws that you are now a member of the select group of owners who can and do change light bulbs ... Timothy for John (Please consider a donation to a charity instead of the Lexus dealer so I now this advice was worth giving to you and the world is not made up of car makers who immitate this kind of manufactured work) Amen....
Greetings: To replace the bulb. With the tailgate in the open position. Access the light assembly by firmly pulling the upper trim piece straight down. The trim piece covers the light assembly a is held in place by six clips. If a clip or two falls out on removal replace it/them as needed in the trim piece for later re-installation. You will see the light assembly clips at the bottom gently press in on the
clips and pull the light assembly out. you now have access to the light socket. remove the socket, replace the bulb, test brake light, re-install socket, re-install the light assembly. make sure wires do not block anchor points for the upper trim piece. Check position and alignment of the six trim piece clips and anchor points. Snap trim piece into place.
1992 Lexus LS400 bulb replacement: Purchase the correct replacement bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the replacement procedure. The owner's manual is the best place to start for bulb replacement. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).
1994 Lexus LS400 brake light bulb replacement: Purchase the correct replacement brake light bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement brake light bulb information. Then consult your owner's manual for the replacement procedure. As simple as it sounds, the owner's manual is the best place to start for brake light bulb replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).
They go in from the rear. remove the light assy.
There are two screws outside the car (near the trunk) and one inside the trunk behind the light that need to be removed. Then slide off th whole panel and replace the bad light.
Remove the battery clamp and the washer bottle. Then you can move the battery a bit and get your hand in to get to the lamp holder.
Louie
you have to replace the parking light bold because is the same as the brake light so just replace the light bold I think is the middle one between turning light and backing light. you have to replace the parking light bold because is the same as the brake light so just replace the light bold I think is the middle one between turning light and backing light.
If you reach behind the light you can twist and pull removing the light bulb socket. Pull out the light and install a new one and do the reverse to install.
If it's the brake light in the boot lid then you have to take the cover off the inside of the boot lid and then you will have access to the light bulbs. If it's the brake light in the rear quarter panel then you open boot lid and unscrew the two bolts holding the light cluster and slide it backwards, then you will have access to the bulbs
if its burnt out, replace it, if not, check the wireing
Open trunk and remove screws that secure light assembly to car. Pull assembly straight back to remove from car. Remove the dead light and replace with proper new light. Install in reverse order of removal.
You can access the brake light bald through the trunk compartment. Remove the trunk liner from the tail light assembly. Push the brake light connector in and turn at the same time. The brake lightbulb will come out. Reverse the process to install the new brake light
Follow the link below, labeled "How to replace a Lexus IS300 tail light"
From what I know (doing my own troubleshooting). It means you need to take it in to get your brake pads replaced.
you dont you get a new car
The fuel capacity for a Lexus LS400 is 22.5-gallons. The low fuel light comes on when there are around 2-gallons of fuel left in the tank. The Lexus LS400 gets around 24-mpg on the open highway.
Lexus IS300 3rd brake light is changed from the back seat. Pry the light up and disconnect wiring. Replace bulb and put back together. Easy job
remove bulb from in side the boot
y
The brake light assembly can be access through the cargo compartment. Remove the cover to the brake light assembly. Take hold of the brake light connector, push in and turn at the same time. The brake light will come out. Reverse the process to install the new brake light.
Looking for Lexus ES300 engine 1993
If your engin light also is on, you need new oxigen sensors!
The center brake light bulbs can be replaced by lifting up on the rear light assembly and pulling towards the front of the car. www.lextechautomotivellc.com