0
What else can I help you with?
Starter c-180 compressor?
Most starter's for anycar will be on the bell housing, The starter uses the tourqe plate to spin the crank.. normally 2 or 3 bolts but if your replacing the starter some need a busing to be replaced and its just better to have a shop do it cause they should have the tools to do so already.
What tools do you need to replace a starter for a 1997 Ford 150?
This is an easy repair. You will need only a basic socket wrench set. Don't forget to disconnect the battery (negative terminal) before you start or you risk causing a short circuit that could injure you or damage the vehicle.
How do you remove a diesel fuel pump on a Mitsubishi pajero 2.8?
This is not advisable if you are not an experienced mechanic as it has to be timed with the need for specialist tools if the timing goes out.
Where is the starter located on the Lexus RX300?
where is the starter located on a 95 ls 400 lexus? and what tools a need to change it? underneath the intake, sucks but it can be changed out within a couple hours if you are knowledgeable
How do you replace a light bulb on a 2001 cbr f4i?
just pull out the socket and the rubber boot, no tools required
Can you replace the ignition in a 95 Mitsubishi mighty max?
Yes, you can replace the ignition system in a 1995 Mitsubishi Mighty Max. The process typically involves removing the existing ignition components, such as the ignition coil and distributor, and installing new ones. It's recommended to consult a repair manual for specific instructions and ensure you have the necessary tools. If you're not comfortable with automotive repairs, seeking assistance from a professional mechanic is advisable.
What tools do you need to replace the starter on a 1989 Oldsmobile 98?
starter on this car should be simple 12pt metric socket and wrench set range from 10mm- 19mm and a pair of jackstands or ramps
Where is the starter located on the 1994 Chrysler LHS 3.5 ltr. and does it require special tools to replace it?
It is on the left side of the block, only tools required are 13 and 15 mm sockets and wrenches.
What does the starter on a Chevrolet Cobalt look like?
The starter motor is behind the crank pulley on the passenger side. This is not a driveway job. You'll need a lift and a few special tools if you're trying to replace it your self.
How do you fix starter on 2003 Mitsubishi Lancer GDI?
Never ever try to repair a starter!! DIY mechanics don't have access to the tools or parts required to repair them. take the old starter to a parts store and have it tested, if they find it to be bad, they can sell you a remanufactured one for around $140. Do this one right and save yourself a bunch of headache
How do you change the timing belt on a Mitsubishi Endeavor?
With tools
How do you replace a ball joint on Mitsubishi Montero LS 95?
Unless you have really big tools or like to be punished, take it to a shop. One of them needs a hydraulic press to remove and install.
Tools need for 2003 galant front pad replacement?
To replace the front brake pads on a 2003 Mitsubishi Galant you will only need a few tools. You will need a jack, tire blocks, a large C-clamp, and a 14 mm socket.
Where is the starter solenoid located on the 1994 Chrysler LHS 3.5 ltr and does it require special tools to replace it?
On the 1994 Chrysler LHS with a 3.5-liter engine, the starter solenoid is typically located on the starter motor itself, mounted on the engine's bell housing. Replacing the solenoid generally does not require special tools, but you will need basic tools like a socket set and wrenches. It's also advisable to disconnect the battery before starting the replacement process for safety.
What tools do you need to remove a starter for 94 Oldsmobile achieva?
Common hand tools.
How do you replace the starter on a 1998 Oldsmobile Bravada?
Simple! 1. disconnect the battery 2. Crawl under vehicle and remove two 14mm bolts holding starter. 3. Remover signal wire from solenoid 4. Remove main power wire 5. Bring new starter under vehicle with you 6. Replace signal wire 7. Replace power wire 8. put starter into hole. 9. Tighten two 14 mm bolts that hold starter 10. Attach battery 11. Set clock on radio 12. Clean tools 13. Bandage cuts on knuckles Piece of cake!
What tools needed to replace fuel pump 99 diamante Mitsubishi?
in the pasanger back seat there is the seat please remobe it and you will see the hole spot when you c an remove with 10 mm sockets and thas the pump
