0
How do you pull a 1996 Ford 2.3 liter harmonic balancer What size bolts are used to pull the balancer?
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Location of ecu ON 1996 Jeep Cherokee 4.0 Liter?
passenger side firewall. behind coolent.
Where is the crankshaft sensor on a 1999 Jeep Cherokee Sport 4 liter?
Hi, My name is Glenn and I show up as anonymous because I did not take the time to sign in. I had access to a 1999 Jeep Wrangler service manual and from what I saw, the crankshaft sensor for the 4.0 liter six cylinder engine is located on the bell housing on the driver's side. It is held in place by a bracket secured by one of bell housing mounti9ng bolts (manual transmission) or two smaller bolts for the manual transmission. It is a hall effect sensor and reads special notches on the flywheel, three sets of four notches to generate the pulses to fire the coil. I would post copies of the pictures from the manual but it would probably be a copyright violation. Also, I am pretty sure that the crankshaft sensor locations are the same for the 4.0 six in the Cherokee. Glenn
Can you use a 1998 Jeep Grand Cherokee 4.0 fuel pump on a 1996 Jeep Grand Cherokee limited 8.0?
nope cant do it. no such thing as an 8.0 liter in a jeep
What is the firing order for a 1996 Grand Cherokee 4.0 liter?
The firing order should be 1-5-3-6-2-4.
Where is the crank shaft sensor in a 1996 jeep Cherokee sport Straight 6. 4.0 liter?
The crank sensor is located on the top of the bell housing on the drivers side.
What would cause an engine vibration when in drive at a stop light on a 1996 Ford Contour 2-liter Zetec with automatic transmission?
check harmonic balancer. check harmonic balancer.
Where is harmonic balancer in 1996 Olds eighty-eight?
The harmonic balancer is located on the front of the crankshaft
Where is the crankshaft sensor on a 1996 Buick 3.8 liter Regal?
It is located behind the harmonic balancer on the front of the engine. You'll need a special puller to remove the balancer.
Where is the Harmonic Balancer on 1996 Toyota Corolla?
On any motor, the harmonic balancer is on the front of the crankshaft. It is what the pulley is bolted to.
Can you put a 1996 Dodge caravan harmonic balancer in a 2002 Dodge stratus?
No
How do you remove the harmonic balancer on a 1996 dodge neon?
loosen the center bolt and get your self a harmonic balancer puller just make sure you loosen the center bolt enough but not too much but you need a balancer puller.
Is 400.00 a fair price to have a harmonic balancer orderded and placed in a 1996 Nissan Sentra?
no its not i paid 50.00 dollars for balancer and put it in about one hour
How do you Remove a Harmonic Balancer on 1996 Chevrolet carprice classic?
You will need a harmonic balancer puller. Remove crankshaft bolt and washer, reinstall bolt without the washer approximately 10 turns. This will protect the threads in the crankshaft. Install puller and remove balancer. You cannot remove the balancer without this puller. They are inexpensive or try to borrow one.
How do you remove the harmonic balancer on a 1996 Dodge Intrepid?
Hi The 3.5L has a tapered shaft, you MUST use a balancer puller or you will damage the pulley. These pullers are under $30 bucks
Which direction do you turn the harmonic balancer bolt on a 1996 Sebring 2.5L engine to remove it?
You turn it counter clockwise to loosen.
How do you install a crankshaft position sensor on a 1996 Pontiac grand-amand where is it located?
If the engine is a 3100 V6, the crankshaft sensor is located behind the harmonic balancer (crankshaft pulley). You'll need a special puller to remove tha balancer. The sensor is attached by two bolts onto the timing cover. Replace sensor and plug it in. Repalce balancer& belts...you're done!
Where is the crank position sensor located on a 1996 Toyota corolla 1.6L?
On the harmonic balancer that's attached to the front of the cranck shaft
