NO! Check the rating on the device and if it says 120V only don't ever dare plug into 240V. Depending on the appliance the results will either be lots of sparks, large flashes or other undesirable side effects.
Another engineer's opinion
That answer above is for USA, Canada and other countries which use the 60Hz electrical service standard, for appliances which were designed to run only on that voltage and nothing higher.
If this question is asking about using 110V to 120V appliances plugged into sockets elsewhere in the world which use the 50Hz 230 to 240V electrical service standard - such as Europe, Australia and many other countries - then the answer is not necessarily NO.
Providing you use the correct type of plug adapter to suit the sockets in each country you visit, if the appliance was designed to run on 110V to 240V services, then the answer is YES.
There are many personal electrical and electronic appliances which were designed to run on voltages within a wide range such as 110 to 240 volts! Just a few examples are: electric razors, hair dryers, battery chargers for digital cameras, mp3 players, etc.
IMPORTANT SAFETY NOTE
Such multi-voltage small appliances should never be used on the 220 to 240 volt outlets in USA or Canada or other countries which use the 60Hz electrical service standard.
Such 220 to 240V outlets are intended for use only by large appliances, such as water heaters, clothes washing machines and dryers, cooking ranges, etc. Such 220 to 240V outlets are quite different in size to 110 to 120V outlets anyway and no adapters should ever be used to try to use those kinds of portable small appliances on 220 to 240V 60Hz.
It may be illegal to do so in some countries or states because:
and
No, you cannot simply change the wall plug to make a 110 volt outlet support a 240 volt appliance. The voltage requirements of the appliance and the outlet must match for safe operation. You would need to install a dedicated 240 volt outlet and ensure that the wiring and circuitry can handle the higher voltage. It is recommended to consult a licensed electrician for this type of electrical work.
There is no need to convert a 110-volt outlet to 115 volts as they are essentially the same. The slight variation is within the normal tolerance range for electrical systems. If you need to use a device that requires 115 volts, you can safely plug it into a 110-volt outlet without the need for an adapter.
No, the plugs are different to prevent this and even if you could the lamp would be very dim.
No. First off, the plug will be different. And even if you replace the plug, it won't work right on the wrong voltage
can you plug a 115 volt into a 110 volt
yes but it will not be as good eg if it is a phone charger it will take longer to charge
no
Yes.
You plug the appliance into the outlet. Israel uses 220-volt household current. Any 110-volt appliances brought from abroad will need a small transformer, which can be bought in appliance stores.
Yes you can. Most electrical appliances will work if supplied with power that's within 10% of their voltage rating.
Yes you can - with a transformer. Maplin Electronics sell a converter that allows you to plug appliances that run on 110V into the normal UK mains. See the related.
The bulb will be about half as bright.
No, the applied 110 volt is too high for a 3 volt appliance. The appliance would burn out right away.
Nominally 110 to 120 volt power strip is okay to connect to a standard outlet.
No conversion needed. These are nominal voltages which range from 110 to 120 volts. It will operate fine on the outlet.
No, you cannot simply change the wall plug to make a 110 volt outlet support a 240 volt appliance. The voltage requirements of the appliance and the outlet must match for safe operation. You would need to install a dedicated 240 volt outlet and ensure that the wiring and circuitry can handle the higher voltage. It is recommended to consult a licensed electrician for this type of electrical work.
There is no need to convert a 110-volt outlet to 115 volts as they are essentially the same. The slight variation is within the normal tolerance range for electrical systems. If you need to use a device that requires 115 volts, you can safely plug it into a 110-volt outlet without the need for an adapter.