answersLogoWhite

0

The suction pressure in a R22 system should typically range between 60-70 psi when the system is operating under normal conditions. It is important to consult the manufacturer's guidelines and consider other factors such as ambient temperature to ensure the system is functioning properly.

User Avatar

AnswerBot

1y ago

What else can I help you with?

Continue Learning about Physics

What is suction and discharge pressure of R-22 Refrigerant?

The typical suction pressure range for R-22 refrigerant is between 68-74 psi, while the discharge pressure ranges from 250-270 psi in a typical operating conditions.


What is the working pressure of r-22?

The standard operating pressure for R-22 refrigerant in air conditioning systems is typically between 68 to 70 psi on the low side and 250 to 270 psi on the high side when the system is running. These values may vary depending on factors such as ambient temperature and specific system requirements.


What is cavitation and priming?

1. PRIMING LOSS: This is the suction loss for a pump whose NPSH is (-ve)2. CAVITATION: It is also suction loss by forming cavity of a volatile liquid whose NPSH(a) is belowNPSH(r) eg..Choking or blockage of suction strainers, closing of suction valve of apump when running.3. VAPOUR LOCK: This is also loss of pumping due to blockage in discharge of a pump..closing of discharge valve and running for more time..running the pump with in adequate minimum flow..liquid above boiling pointHence Cavitation, Vapour Lock and Primimng loss are different


The minimum safety-relief pressure for a R-410A cylinder is?

The minimum safety-relief pressure for a R-410A cylinder is typically around 550 psi. This pressure is set to prevent over-pressurization of the cylinder, ensuring safe handling and storage of the refrigerant. It is important to always refer to the manufacturer's guidelines for specific pressure requirements.


What internal pressure of a cylinder with one ounce of liquid R-410A refrigerant which has been sitting in a 100 degree Fahrenheit truck is?

The internal pressure of a cylinder containing R-410A refrigerant with one ounce of liquid will depend on various factors such as the temperature-pressure relationship for R-410A and any external conditions affecting the temperature of the refrigerant. However, at 100 degrees Fahrenheit, the pressure of R-410A is approximately 228 psi.

Related Questions

What is suction and discharge pressure of R-22 Refrigerant?

The typical suction pressure range for R-22 refrigerant is between 68-74 psi, while the discharge pressure ranges from 250-270 psi in a typical operating conditions.


How much should be Condenser pressure in an ac with r-22 refrigerant?

300psi


To maintain 40 degree evaporator coil temperature what is the suction pressure?

The suction pressure required to maintain a 40 degree evaporator coil temperature depends on the refrigerant being used, as different refrigerants have different pressure-temperature characteristics. A typical range for R-22 refrigerant would be around 55-60 psig. It is important to consult the specific pressure-temperature chart for the refrigerant being used.


How do you calculate suction pressure for air theoretically?

Air has a pressure, but not a suction pressure. Air pressure is measured with a barometer, you do not calculate it. Suction pressure is a concept which applies to a pump. Suction pressure = static pressure + surface pressure - vapour pressure - friction pressure.


What is the suction pressure of 407c gas?

The suction pressure of R-407C gas typically ranges from 70 to 110 psi, depending on factors such as ambient temperature, system design, and operating conditions. It is important to consult the manufacturer's guidelines and specifications for the specific equipment or system being used to determine the appropriate suction pressure.


On a 95 degree day on r-22 what is normal pressure?

250


What the 134a gas normal suction and discharge pressure?

For R-134a gas in a typical air conditioning system, normal suction pressure ranges from 25 to 40 psi, while discharge pressure ranges from 175 to 260 psi. These pressures can vary based on factors such as ambient temperature, equipment efficiency, and system design.


What is the purpose of suction?

I am in school with maddy R


What is the purpose of suction filter?

I am in school with maddy R


What refrigerants has the lowest boiling temperatures at atmospheric pressure R-12 R-22 R-134a R-502?

This is R-502 with a boiling point at -45 0C.


Will r-134a coolant damage your r-22 coolant system?

Standard R-134a coolant will damage an R-22 coolant system because they are chemically different. They also have different characteristics for pressure and freezing point.


Total surface area of a cylinder?

1500 sq in of surface R-22 at120F tons of pressure